Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0242208 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A8196  Hybrid/EV Battery Cooling Fan 1 Component Internal Failure  


DESCRIPTION

Refer to the description for DTC P0A8111.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A8111

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A8196 Hybrid/EV Battery Cooling Fan 1 Component Internal Failure The battery cooling blower assembly is malfunctioning and the actual speed is not within the specified range of the target speed calculated by the ECU.*
*: This DTC is not stored when "Hybrid Battery Cooling Fan Frequency" is excessively low or high.
(1 trip detection logic)
·

Battery voltage sensor

·

Hybrid vehicle control ECU

·

Battery cooling blower assembly

·

No. 1 HV battery intake filter

·

No. 1 Hybrid battery intake duct

·

Wire harness or connector


Does not come on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P0A8196
·

Hybrid Battery Cooling Fan Drive Request

·

Hybrid Battery Cooling Fan 1 Drive Status

·

Hybrid Battery Cooling Fan Frequency



The following items can be helpful when performing repairs:

Data List
·

Hybrid Battery Temperature 1 to 3

·

BATT Voltage


HINT:

"Hybrid Battery Cooling Fan Frequency" is detected when the battery cooling blower assembly is operating and its value changes in proportion to the battery cooling blower assembly rotation speed.


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Turn the power switch on (IG) and turn the GTS on.

6.

Enter the following menus: Powertrain / Hybrid Control / Active Test / Control the Hybrid Battery Cooling Fan.

7.

Turn the battery cooling blower assembly off, then operate it in fan mode 1 through 6 and wait for 5 minutes or more.

HINT:

Operation of the battery cooling blower assembly can be confirmed by checking if air is sucked into the air intake port of the intake duct.


8.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

9.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A8111.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A8111

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

Result:
Result Proceed to
P0AFC00 or P0AFC96 is not output. A
P0AFC00 or P0AFC96 is also output. B


e.

Turn the power switch off.



A

2.CHECK DUCT AND BLOWER

B

2.CHECK DUCT AND BLOWER
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


c.

Check that the No. 1 HV battery intake filter, battery cooling blower assembly and No. 1 hybrid battery intake duct are not disconnected, damaged, or clogged with foreign matter.

A376403C02
5.813,1.229 6.292,1.229 true 4.385,1.427 4.865,1.427 true 2.115,1.927 2.594,1.927 true 2.698,1.854 2.99,2.083 0.292,0.229 10 true *1 4.073,1.344 4.354,1.604 0.281,0.26 10 true *2 6.365,1.156 6.698,1.385 0.333,0.229 10 true *3
*1 No. 1 HV Battery Intake Filter *2 Battery Cooling Blower Assembly
*3 No. 1 Hybrid Battery Intake duct - -



d.

Install the rear seat cushion assembly.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY)

NG

CORRECT THE PROBLEM

3.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - BATTERY COOLING BLOWER ASSEMBLY)

OK

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY COOLING BLOWER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - BATTERY COOLING BLOWER ASSEMBLY)

OK

5.CHECK HYBRID VEHICLE CONTROL ECU (GROUND SHORT CHECK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HYBRID VEHICLE CONTROL ECU (GROUND SHORT CHECK)

b.

Measure the resistance according to the value(s) in the table below.

A365590C08
3.417,0.354 3.771,0.604 0.354,0.25 2.865,1.281 1.906,0.521 true 4.042,1.604 3.667,2.375 true 2.99,1.24 2.583,0.469 true 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 3.51,0.385 4.063,0.865 0.552,0.479 10 false F2 1.594,0.417 2.208,0.615 0.615,0.198 10 false E01 3.542,2.417 4.083,2.698 0.542,0.281 10 false SI0 2.302,0.385 2.917,0.583 0.615,0.198 10 false E02
*a Component without harness connected
(Hybrid Vehicle Control ECU)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
F2-38(SI0) - F2-12(E01) Power switch off 10 kΩ or higher
F2-38(SI0) - F2-11(E02) Power switch off 10 kΩ or higher



c.

Install the hybrid vehicle control ECU.


Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (COOLING FAN FREQUENCY)

NG

6.READ VALUE USING GTS (COOLING FAN FREQUENCY)

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A8111

Result:
Result Proceed to
Both of the value in the Data List (Hybrid Battery Cooling Fan Frequency) and the actual measured value at the battery ECU assembly connector are 0 Hz. A
Other than above B



A

7.CHECK BATTERY VOLTAGE SENSOR

B

8.CHECK BATTERY VOLTAGE SENSOR (FREQUENCY)
7.CHECK BATTERY VOLTAGE SENSOR

OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG

8.CHECK BATTERY VOLTAGE SENSOR (FREQUENCY)

OK

REPLACE BATTERY COOLING BLOWER ASSEMBLY

NG