Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM
RM3210E _51 Engine / Hybrid System _047524 HYBRID / BATTERY CONTROL _0242208 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0ABF28  Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure  


DESCRIPTION

Refer to the description for DTC P0ABF11.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0ABF11

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0ABF28 Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure The offset value of the battery current sensor is excessively large.
(1 trip detection logic)
·

Battery voltage sensor

·

HV battery junction block assembly


Comes on Master Warning Light:
Comes on

Related Data List
DTC No. Data List
P0ABF28
·

Hybrid Battery Current for Hybrid Battery Control *1

·

Hybrid Battery Current



HINT:

*1: The value of "Hybrid Battery Current *1" will be approximately 0 A when the power switch is on (IG) (READY off).


CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>UTILITY


1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG) and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for 2 minutes or more.

5.

Drive the vehicle on urban roads for approximately 10 minutes.

6.

Turn the power switch off and wait for 2 minutes or more.

7.

Turn the power switch on (IG) and turn the GTS on.

8.

With power switch on (IG) and wait for 10 seconds or more.

9.

Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.

10.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.




PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

e.

Turn the power switch off.


Result:
Result Proceed to
P0AFC00, P0AFC96 or P0A9563 is not output. A
P0AFC00, P0AFC96 or P0A9563 is also output. B



A

2.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)

B

2.CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE SENSOR - HV BATTERY JUNCTION BLOCK ASSEMBLY)

OK

3.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR (IB))

NG

3.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY (BATTERY CURRENT SENSOR (IB))
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 1 hybrid battery exhaust duct.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
A368051C32
1.677,0.208 2.115,0.438 0.438,0.229 1.135,1.667 1.677,0.979 true 1.688,0.875 1.26,0.427 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 1.792,0.24 2.188,0.552 0.396,0.313 10 false z9 0.938,1.708 1.271,1.969 0.333,0.26 10 false GIB 0.958,0.344 1.292,0.604 0.333,0.26 10 false VIB
*a Component with harness connected
(Battery Voltage Sensor)


Using a toyota electrical tester set to 40 V, measure the VIB voltage according to the value(s) in the table below.

Tester Connection Tester Connection
z9-6 (VIB) - z9-12 (GIB) Power switch on (IG)

NOTICE:
·

Turning the power switch on (IG) with the service plug grip removed causes other DTCs to be stored. Clear the DTCs after performing this inspection.

·

Be sure to set the toyota electrical tester to 40 V when performing this test.




f.
A368051C33
1.635,0.177 2.073,0.406 0.438,0.229 1.135,1.667 1.677,0.979 true 1.76,0.865 1.188,0.365 true 0.104,0.063 0.5,0.375 0.396,0.313 10 false *a 1.792,0.198 2.188,0.51 0.396,0.313 10 false z9 0.99,1.688 1.323,1.948 0.333,0.26 10 false GIB 0.969,0.271 1.406,0.625 0.438,0.354 10 false IB0
*a Component with harness connected
(Battery Voltage Sensor)


Using a toyota electrical tester set to 4 V, measure the IB0 voltage according to the value(s) in the table below.

Tester Connection Tester Connection
z9-5(IB0) - z9-12(GIB) Power switch on (IG)

NOTICE:

Be sure to set the toyota electrical tester to 4 V when performing this test.



g.

Compare the measured values of the IB0 terminal voltage and VIB terminal voltage using the following formula:

IB0 voltage - VIB Voltage / 2 = less than 0.081 V
IB0 voltage - VIB Voltage / 2 = -0.081 V or higher


Result:
Result Proceed to
Within the specified range above A
Other than above B


h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.


j.

Install the No. 1 hybrid battery exhaust duct.


HINT:

When the power switch is on (IG) the actual current will be approximately 0 A. The following graph shows the relation of the actual output voltage of the battery current sensor terminal IB0 and actual current used for DTC judgment.

A382906E03
1.708,0.281 2.625,0.729 0.917,0.448 10 false Voltage 4.844,2.188 5.865,2.698 1.021,0.51 10 false Current 1.583,1.219 2.5,1.667 0.917,0.448 10 false VIB/2 3.177,2.656 4.094,3.104 0.917,0.448 10 false -4 A 3.896,2.656 4.813,3.115 0.917,0.458 10 false +4 A 3.563,2.656 4.479,3.104 0.917,0.448 10 false 0 A 0.625,2.813 3.615,3.052 2.99,0.24 10 false Battery Current Sensor Normal Range 0.615,3.073 3.604,3.313 2.99,0.24 10 false Toyota electrical tester margin of error 0.625,3.344 3.635,3.646 3.01,0.302 10 false Battery current sensor operation malfunction



A

4.REPLACE BATTERY VOLTAGE SENSOR

B

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

4.REPLACE BATTERY VOLTAGE SENSOR

NEXT

5.SIMULATION TEST
5.SIMULATION TEST
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Clear the DTCs and freeze frame data.

Powertrain > Hybrid Control > Clear DTCs
50002 397

e.

Drive the vehicle on urban roads for approximately 10 minutes.


f.

Turn the power switch off and wait for 2 minutes or more.


g.

Turn the power switch on (IG) and wait for 10 seconds or more.


Result:
Proceed to
NEXT



NEXT

6.RECONFIRM DTC OUTPUT (HYBRID CONTROL)
6.RECONFIRM DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read output DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 397

e.

Turn the power switch off.


Result:
Result Proceed to
P0ABF28 is not output. A
P0ABF28 is output. B



A

COMPLETED

B

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY