The main body ECU (multiplex network body ECU) detects whether either the rear doors are open or closed based on the condition of the rear door courtesy light switch assemblies condition and then sends the rear door status signal to the combination meter assembly. The combination meter assembly detects rear seat belt state. The rear seat belt warning light on the combination meter assembly illuminates or turns off in accordance with the rear door state, vehicle speed and rear seat belt state.
The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| RR Door Courtesy SW | Rear door courtesy light switch RH | ON or OFF | ON: Rear door RH open
OFF: Rear door RH closed |
- |
| RL Door Courtesy SW | Rear door courtesy light switch LH | ON or OFF | ON: Rear door LH open
OFF: Rear door LH closed |
- |
| Tester Display |
|---|
| RR Door Courtesy SW |
| RL Door Courtesy SW |
ON or OFF appears on the GTS screen according to the rear door condition.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Rear Seat Belt Warning Light (Combination Meter Assembly) |
| *a | LH |
| *b | Center |
| *c | RH |
Check the rear seat belt warning function.
| Result | Proceed to |
|---|---|
| The rear seat belt warning lights operate normally | A |
| The rear seat belt warning lights (all seats) do not operate normally | B |
| The rear seat belt warning light (RH) does not operate normally | C |
| The rear seat belt warning light (center) does not operate normally | D |
| The rear seat belt warning light (LH) does not operate normally | E |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
D
E
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| 2nd-Row Seatbelt Buckle (R) | Rear RH seat belt buckle switch signal | ON or OFF | ON: Rear RH seat belt fastened
OFF: Rear RH seat belt not fastened |
- |
| Tester Display |
|---|
| 2nd-Row Seatbelt Buckle (R) |
| Result | Proceed to |
|---|---|
| ON or OFF does not appear on the GTS screen according to the rear seat belt condition | A |
| ON or OFF appears on the GTS screen according to the rear seat belt condition | B |
A
B
Disconnect the F6 meter circuit plate connector.
Disconnect the M25 rear seat inner belt assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F6-10 (RRSB) - M25-5 (RBR+) | Always | Below 1 Ω |
| F6-10 (RRSB) or M25-5 (RBR+) - Body ground | Always | 10 kΩ or higher |
| M25-4 (RBR-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| 2nd-Row Seatbelt Buckle (C) | Rear center seat belt buckle switch signal | ON or OFF | ON: Rear center seat belt fastened
OFF: Rear center seat belt not fastened |
- |
| Tester Display |
|---|
| 2nd-Row Seatbelt Buckle (C) |
| Result | Proceed to |
|---|---|
| ON or OFF does not appear on the GTS screen according to the rear seat belt condition | A |
| ON or OFF appears on the GTS screen according to the rear seat belt condition | B |
A
B
Disconnect the F6 meter circuit plate connector.
Disconnect the M27 rear seat inner with center belt assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F6-11 (RCSB) - M27-1 (CBR+) | Always | Below 1 Ω |
| F6-11 (RCSB) or M27-1 (CBR+) - Body ground | Always | 10 kΩ or higher |
| M27-2 (CBR-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| 2nd-Row Seatbelt Buckle (L) | Rear LH seat belt buckle switch signal | ON or OFF | ON: Rear LH seat belt fastened
OFF: Rear LH seat belt not fastened |
- |
| Tester Display |
|---|
| 2nd-Row Seatbelt Buckle (L) |
| Result | Proceed to |
|---|---|
| ON or OFF does not appear on the GTS screen according to the rear seat belt condition | A |
| ON or OFF appears on the GTS screen according to the rear seat belt condition | B |
A
B
Disconnect the F6 meter circuit plate connector.
Disconnect the M26 rear seat inner with center belt assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F6-12 (RLSB) - M26-5 (LBR+) | Always | Below 1 Ω |
| F6-12 (RLSB) or M26-5 (LBR+) - Body ground | Always | 10 kΩ or higher |
| M26-4 (LBR-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG