Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2016.08
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0239522 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Speaker Circuit  


DESCRIPTION

for 6 Speakers

If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly, telematics transceiver* or speakers.


for 10 Speakers

If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.

Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, telematics transceiver* or speakers.


*: w/ Manual (SOS) Switch


WIRING DIAGRAM

for 6 Speakers
E352439E02
4.281,0.979 4.656,1.156 0.375,0.177 10 false SPI+ 3.698,0.969 4.135,1.135 0.438,0.167 10 false SPO+ 3.698,1.823 4.073,2 0.375,0.177 10 false SPO- 5.833,0.969 6.208,1.146 0.375,0.177 10 false FR+ 5.823,1.844 6.198,2.021 0.375,0.177 10 false FR- 3.354,2.063 3.729,2.24 0.375,0.177 10 false F36 5.823,3.583 6.198,3.76 0.375,0.177 10 false FL+ 5.823,4.458 6.198,4.635 0.375,0.177 10 false FL- 5.833,5.51 6.208,5.688 0.375,0.177 10 false RR+ 5.833,6.146 6.208,6.323 0.375,0.177 10 false RR- 5.813,7.021 6.188,7.198 0.375,0.177 10 false RL+ 5.823,7.656 6.198,7.833 0.375,0.177 10 false RL- 5.531,1.667 5.688,1.823 0.156,0.156 10 false 5 5.531,3.396 5.688,3.552 0.156,0.156 10 false 2 5.521,0.781 5.677,0.938 0.156,0.156 10 false 1 5.531,4.271 5.719,4.417 0.188,0.146 10 false 6 5.531,5.302 5.719,5.448 0.188,0.146 10 false 1 5.542,5.948 5.729,6.094 0.188,0.146 10 false 3 5.531,6.833 5.719,6.979 0.188,0.146 10 false 2 5.531,7.469 5.719,7.615 0.188,0.146 10 false 6 4.656,0.844 4.813,1 0.156,0.156 10 false 2 4.656,1.74 4.813,1.896 0.156,0.156 10 false 3 3.563,0.854 3.719,1.01 0.156,0.156 10 false 5 2.396,0.875 2.552,1.031 0.156,0.156 10 false 4 0.979,0.885 1.135,1.042 0.156,0.156 10 false 3 0.979,1.729 1.135,1.885 0.156,0.156 10 false 1 0.5,1.698 0.656,1.854 0.156,0.156 10 false 2 0.479,1.094 0.635,1.25 0.156,0.156 10 false 1 1.792,3.698 1.958,3.896 0.167,0.198 10 false 1 1.813,4.344 1.979,4.542 0.167,0.198 10 false 2 2.313,4.365 2.479,4.563 0.167,0.198 10 false 1 4.552,3.479 4.719,3.677 0.167,0.198 10 false 4 4.604,4.323 4.771,4.521 0.167,0.198 10 false 2 1.792,5.51 1.958,5.708 0.167,0.198 10 false 1 1.813,6.135 1.979,6.333 0.167,0.198 10 false 2 1.792,7.021 1.958,7.219 0.167,0.198 10 false 1 1.813,7.646 1.979,7.844 0.167,0.198 10 false 2 2.406,1.74 2.563,1.896 0.156,0.156 10 false 2 2.323,3.479 2.49,3.677 0.167,0.198 10 false 3 0.063,2.229 1.375,2.708 1.313,0.479 10 false Front No. 1 Speaker Assembly RH 1.51,2.375 2.781,2.896 1.271,0.521 10 false Front No. 2 Speaker Assembly RH 3.354,2.25 4.917,2.542 1.563,0.292 10 false Telematics Transceiver*1 3.552,1.74 3.708,1.896 0.156,0.156 10 false 6 5.469,0.969 5.771,1.135 0.302,0.167 10 false F32 5.479,1.844 5.781,2.01 0.302,0.167 10 false F32 5.458,3.573 5.76,3.74 0.302,0.167 10 false F32 5.458,4.458 5.76,4.625 0.302,0.167 10 false F32 5.469,5.51 5.771,5.677 0.302,0.167 10 false F33 5.469,6.135 5.771,6.302 0.302,0.167 10 false F33 5.448,7.01 5.75,7.177 0.302,0.167 10 false F33 5.458,7.646 5.76,7.813 0.302,0.167 10 false F33 3.073,3.865 4.271,4.479 1.198,0.615 10 false Front No. 2 Speaker Assembly LH 0.344,3.979 1.604,4.396 1.26,0.417 10 false Front No. 1 Speaker Assembly LH 0.823,5.781 1.719,6.323 0.896,0.542 10 false Rear Speaker Assembly RH 0.813,7.281 1.667,7.688 0.854,0.406 10 false Rear Speaker Assembly LH 3.125,1.063 3.281,1.219 0.156,0.156 10 false *1 3.115,1.927 3.271,2.083 0.156,0.156 10 false *1 4.854,1.927 5.01,2.083 0.156,0.156 10 false *1 4.833,1.052 4.99,1.208 0.156,0.156 10 false *1 3.979,0.542 4.188,0.698 0.208,0.156 10 false *2 3.99,2.771 4.198,2.927 0.208,0.156 10 false *2 1.5,2.219 1.875,2.396 0.375,0.177 10 false G3 0.063,2.063 0.438,2.24 0.375,0.177 10 false I1 0.333,3.802 0.708,3.979 0.375,0.177 10 false J1 3.063,3.688 3.438,3.865 0.375,0.177 10 false G6 0.813,5.563 1.188,5.74 0.375,0.177 10 false K4 0.813,7.083 1.188,7.26 0.375,0.177 10 false L5 0.25,8.208 2.021,8.448 1.771,0.24 10 false *1: w/ Manual (SOS) Switch 2.417,8.208 4.229,8.531 1.813,0.323 10 false *2: w/o Manual (SOS) Switch 1.135,0.875 1.292,1.031 0.156,0.156 10 false + 2.469,3.479 2.625,3.635 0.156,0.156 10 false + 1.135,1.771 1.292,1.927 0.156,0.156 10 false - 2.49,4.365 2.646,4.521 0.156,0.156 10 false - 4.302,1.823 4.677,2 0.375,0.177 10 false SPI- 4.104,3.49 4.521,3.667 0.417,0.177 10 false TWL+ 4.135,4.365 4.521,4.563 0.385,0.198 10 false TWL- 1.938,0.865 2.354,1.042 0.417,0.177 10 false TWR+ 1.958,1.75 2.375,1.927 0.417,0.177 10 false TWR- 5.292,8.156 7,8.542 1.708,0.385 10 false Radio and Display Receiver Assembly

for 10 Speakers
E334506E03
0.302,0.5 0.615,0.698 0.313,0.198 10 false G4 0.302,2.417 0.615,2.615 0.313,0.198 10 false G5 0.5,3.521 0.813,3.719 0.313,0.198 10 false I1 0.479,4.594 0.792,4.792 0.313,0.198 10 false J1 2.927,2.344 3.24,2.542 0.313,0.198 10 false 4 2.927,2.99 3.24,3.188 0.313,0.198 10 false 3 5.698,7.208 6.01,7.406 0.313,0.198 10 false 27 5.688,6.573 6,6.771 0.313,0.198 10 false 12 5.698,6.156 6.01,6.354 0.313,0.198 10 false 26 5.698,5.521 6.01,5.719 0.313,0.198 10 false 11 5.698,5.104 6.01,5.302 0.313,0.198 10 false 23 5.771,4.469 6.083,4.667 0.313,0.198 10 false 8 5.719,4.052 6.031,4.25 0.313,0.198 10 false 30 5.708,3.417 6.021,3.615 0.313,0.198 10 false 15 5.719,3 6.031,3.198 0.313,0.198 10 false 25 5.708,2.365 6.021,2.563 0.313,0.198 10 false 10 5.708,1.115 6.021,1.313 0.313,0.198 10 false 28 5.708,0.479 6.021,0.677 0.313,0.198 10 false 13 4.438,0.594 4.865,0.823 0.427,0.229 10 false SPI+ 5.823,7.813 6.135,8.01 0.313,0.198 10 false F60 2.917,0.479 3.229,0.677 0.313,0.198 10 false 4 2.927,1.125 3.24,1.323 0.313,0.198 10 false 3 3.688,0.49 4,0.688 0.313,0.198 10 false 5 3.688,1.125 4,1.323 0.313,0.198 10 false 6 4.229,0.156 4.542,0.354 0.313,0.198 10 false *2 3.406,0.698 3.719,0.896 0.313,0.198 10 false *1 3.406,1.323 3.719,1.521 0.313,0.198 10 false *1 5.052,1.333 5.365,1.531 0.313,0.198 10 false *1 5.063,0.698 5.375,0.896 0.313,0.198 10 false *1 4.833,1.115 5.146,1.313 0.313,0.198 10 false 3 4.823,0.479 5.135,0.677 0.313,0.198 10 false 2 3.875,0.604 4.302,0.833 0.427,0.229 10 false SPO+ 3.885,1.198 4.313,1.427 0.427,0.229 10 false SPO- 4.458,1.198 4.885,1.427 0.427,0.229 10 false SPI- 3.406,1.542 3.833,1.771 0.427,0.229 10 false F36 3.406,1.698 5.656,1.99 2.25,0.292 10 false Telematics Transceiver*1 5.958,0.583 6.396,0.844 0.438,0.26 10 false TWR+ 5.958,1.219 6.396,1.479 0.438,0.26 10 false TWR- 5.958,2.438 6.396,2.698 0.438,0.26 10 false TWL+ 5.958,3.083 6.396,3.344 0.438,0.26 10 false TWL- 5.969,3.51 6.406,3.771 0.438,0.26 10 false FR+ 5.969,4.146 6.406,4.406 0.438,0.26 10 false FR- 5.969,4.563 6.406,4.823 0.438,0.26 10 false FL+ 5.969,5.177 6.406,5.438 0.438,0.26 10 false FL- 5.958,5.625 6.396,5.885 0.438,0.26 10 false RR+ 5.969,6.25 6.406,6.51 0.438,0.26 10 false RR- 5.969,6.688 6.406,6.948 0.438,0.26 10 false RL+ 5.969,7.323 6.406,7.583 0.438,0.26 10 false RL- 0.49,5.552 0.802,5.75 0.313,0.198 10 false K4 0.49,6.667 0.802,6.865 0.313,0.198 10 false L5 1.917,3.542 2.229,3.74 0.313,0.198 10 false 1 1.927,4.208 2.24,4.406 0.313,0.198 10 false 2 1.917,4.583 2.229,4.781 0.313,0.198 10 false 1 1.938,5.229 2.25,5.427 0.313,0.198 10 false 2 2.917,5.51 3.229,5.708 0.313,0.198 10 false 1 2.917,6.583 3.229,6.781 0.313,0.198 10 false 1 2.927,6.167 3.24,6.365 0.313,0.198 10 false 2 2.927,7.219 3.24,7.417 0.313,0.198 10 false 2 0.302,0.667 1.573,1.167 1.271,0.5 10 false Front No. 2 Speaker Assembly RH 0.302,2.573 1.573,3.073 1.271,0.5 10 false Front No. 2 Speaker Assembly LH 0.49,3.698 1.76,4.198 1.271,0.5 10 false Front No. 1 Speaker Assembly RH 0.479,4.76 1.75,5.26 1.271,0.5 10 false Front No. 1 Speaker Assembly LH 0.49,5.719 1.375,6.135 0.885,0.417 10 false Rear Speaker Assembly RH 0.333,7.969 2.802,8.25 2.469,0.281 10 false *1: w/ Manual (SOS) Switch 0.333,8.313 2.802,8.594 2.469,0.281 10 false *2: w/o Manual (SOS) Switch 5.813,7.969 7.01,8.531 1.198,0.563 10 false Stereo Component Amplifier Assembly 0.479,6.823 1.365,7.24 0.885,0.417 10 false Rear Speaker Assembly LH 4.229,2.156 4.542,2.354 0.313,0.198 10 false *2

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>PRECAUTION


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for 6 Speakers A
for 10 Speakers B




A

2.CHECK SPEAKER (OPERATION CHECK)

B

13.CHECK SPEAKER (OPERATION CHECK)
2.CHECK SPEAKER (OPERATION CHECK)
a.
E268474

Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>OPERATION CHECK


b.

Perform the operation check above and determine the speaker that is not operating.

Result:
Not Operating Speaker Proceed to
Front No. 1 speaker assembly or front No. 2 speaker assembly (w/ Manual (SOS) Switch) A
Front No. 1 speaker assembly or front No. 2 speaker assembly (w/o Manual (SOS) Switch) B
Rear speaker assembly C


HINT:

If sound cannot be heard from any speaker, inspect all of them.




A

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER - FRONT NO. 2 SPEAKER ASSEMBLY)

B

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)

C

11.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER - FRONT NO. 2 SPEAKER ASSEMBLY)
a.

Disconnect the F32 radio and display receiver assembly connector.


b.

Disconnect the F36 telematics transceiver connector.


c.

Disconnect the G3 and G6 front No. 2 speaker assembly connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F32-1 (FR+) - F36-2 (SPI+) Always Below 1 Ω
F32-5 (FR-) - F36-3 (SPI-) Always Below 1 Ω
F36-5 (SPO+) - G3-4 (TWR+) Always Below 1 Ω
F36-6 (SPO-) - G3-2 (TWR-) Always Below 1 Ω
F32-2 (FL+) - G6-4 (TWL+) Always Below 1 Ω
F32-6 (FL-) - G6-2 (TWL-) Always Below 1 Ω
F32-1 (FR+) or F36-2 (SPI+) - Body ground Always 10 kΩ or higher
F32-5 (FR-) or F36-3 (SPI-) - Body ground Always 10 kΩ or higher
F36-5 (SPO+) or G3-4 (TWR+) - Body ground Always 10 kΩ or higher
F36-6 (SPO-) or G3-2 (TWR-) - Body ground Always 10 kΩ or higher
F32-2 (FL+) or G6-4 (TWL+) - Body ground Always 10 kΩ or higher
F32-6 (FL-) or G6-2 (TWL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
a.

Disconnect the I1 and J1 front No. 1 speaker assembly connectors.


b.

Disconnect the G3 and G6 front No. 2 speaker assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I1-1 - G3-3 (+) Always Below 1 Ω
I1-2 - G3-1 (-) Always Below 1 Ω
J1-1 - G6-3 (+) Always Below 1 Ω
J1-2 - G6-1 (-) Always Below 1 Ω
I1-1 or G3-3 (+) - Body ground Always 10 kΩ or higher
I1-2 or G3-1 (-) - Body ground Always 10 kΩ or higher
J1-1 or G6-3 (+) - Body ground Always 10 kΩ or higher
J1-2 or G6-1 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT TELEMATICS TRANSCEIVER
a.

Remove the telematics transceiver.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.
E169849C05
2.51,1.917 2.677,1.5 2.677,1.5 2.75,1.5 false 2.302,1.906 2.188,1.5 2.188,1.5 2.083,1.5 false 0.781,1.906 0.667,1.5 0.667,1.5 0.583,1.5 false 0.979,1.917 1.146,1.5 1.146,1.5 1.25,1.5 false 2.781,1.417 3.146,1.635 0.365,0.219 10 false SPI+ 1.781,1.417 2.156,1.583 0.375,0.167 10 false SPI- 1.292,1.417 1.781,1.583 0.49,0.167 10 false SPO+ 0.198,1.427 0.667,1.646 0.469,0.219 10 false SPO- 0.167,0.177 0.448,0.417 0.281,0.24 10 false *a
*a Component without harness connected
(Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SPI+) - 5 (SPO+) Always Below 1 Ω
3 (SPI-) - 6 (SPO-) Always Below 1 Ω
2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
2 (SPI+) or 5 (SPO+) - Body ground Always 10 kΩ or higher
3 (SPI-) or 6 (SPO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

6.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Inspect the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION


c.

Check that the malfunction disappears when a new or known good front No. 2 speaker assembly is installed.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG

7.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
7.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.

Inspect the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
a.

Disconnect the F32 radio and display receiver assembly connector.


b.

Disconnect the I1 and J1 front No. 1 speaker assembly connectors.


c.

Disconnect the G3 and G6 front No. 2 speaker assembly connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F32-1 (FR+) - G3-4 (TWR+) Always Below 1 Ω
F32-5 (FR-) - G3-2 (TWR-) Always Below 1 Ω
F32-2 (FL+) - G6-4 (TWL+) Always Below 1 Ω
F32-6 (FL-) - G6-2 (TWL-) Always Below 1 Ω
I1-1 - G3-3 (+) Always Below 1 Ω
I1-2 - G3-1 (-) Always Below 1 Ω
J1-1 - G6-3 (+) Always Below 1 Ω
J1-2 - G6-1 (-) Always Below 1 Ω
F32-1 (FR+) or G3-4 (TWR+) - Body ground Always 10 kΩ or higher
F32-5 (FR-) or G3-2 (TWR-) - Body ground Always 10 kΩ or higher
F32-2 (FL+) or G6-4 (TWL+) - Body ground Always 10 kΩ or higher
F32-6 (FL-) or G6-2 (TWL-) - Body ground Always 10 kΩ or higher
I1-1 or G3-3 (+) - Body ground Always 10 kΩ or higher
I1-2 or G3-1 (-) - Body ground Always 10 kΩ or higher
J1-1 or G6-3 (+) - Body ground Always 10 kΩ or higher
J1-2 or G6-1 (-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Inspect the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION


c.

Check that the malfunction disappears when a new or known good front No. 2 speaker assembly is installed.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG

10.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
10.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.

Inspect the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)
a.

Disconnect the F33 radio and display receiver assembly connector.


b.

Disconnect the L5 and K4 rear speaker assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F33-1 (RR+) - K4-1 Always Below 1 Ω
F33-3 (RR-) - K4-2 Always Below 1 Ω
F33-2 (RL+) - L5-1 Always Below 1 Ω
F33-6 (RL-) - L5-2 Always Below 1 Ω
F33-1 (RR+) or K4-1 - Body ground Always 10 kΩ or higher
F33-3 (RR-) or K4-2 - Body ground Always 10 kΩ or higher
F33-2 (RL+) or L5-1 - Body ground Always 10 kΩ or higher
F33-6 (RL-) or L5-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.INSPECT REAR SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT REAR SPEAKER ASSEMBLY
a.

Remove the rear speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL


b.

Inspect the rear speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

13.CHECK SPEAKER (OPERATION CHECK)
a.
E268474

Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>OPERATION CHECK


b.

Perform the operation check above and determine the speaker that is not operating.

Result:
Not Operating Speaker Proceed to
Front No. 2 speaker assembly (w/ Manual (SOS) Switch) A
Front No. 2 speaker assembly (w/o Manual (SOS) Switch) B
Front No. 1 speaker assembly C
Rear speaker assembly D


HINT:

If sound cannot be heard from any speaker, inspect all of them.




A

14.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEMATICS TRANSCEIVER - FRONT NO. 2 SPEAKER ASSEMBLY)

B

17.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)

C

19.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)

D

21.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)
14.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEMATICS TRANSCEIVER - FRONT NO. 2 SPEAKER ASSEMBLY)
a.

Disconnect the F60 stereo component amplifier assembly connector.


b.

Disconnect the F36 telematics transceiver connector.


c.

Disconnect the G4 and G5 front No. 2 speaker assembly connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F60-13 (TWR+) - F36-2 (SPI+) Always Below 1 Ω
F60-28 (TWR-) - F36-3 (SPI-) Always Below 1 Ω
F36-5 (SPO+) - G4-4 Always Below 1 Ω
F36-6 (SPO-) - G4-3 Always Below 1 Ω
F60-10 (TWL+) - G5-4 Always Below 1 Ω
F60-25 (TWL-) - G5-3 Always Below 1 Ω
F60-13 (TWR+) or F36-2 (SPI+) - Body ground Always 10 kΩ or higher
F60-28 (TWR-) or F36-3 (SPI-) - Body ground Always 10 kΩ or higher
F36-5 (SPO+) or G4-4 - Body ground Always 10 kΩ or higher
F36-6 (SPO-) or G4-3 - Body ground Always 10 kΩ or higher
F60-10 (TWL+) or G5-4 - Body ground Always 10 kΩ or higher
F60-25 (TWL-) or G5-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.INSPECT TELEMATICS TRANSCEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT TELEMATICS TRANSCEIVER
a.

Remove the telematics transceiver.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


b.
E169849C05
2.51,1.917 2.677,1.5 2.677,1.5 2.75,1.5 false 2.302,1.906 2.188,1.5 2.188,1.5 2.083,1.5 false 0.781,1.906 0.667,1.5 0.667,1.5 0.583,1.5 false 0.979,1.917 1.146,1.5 1.146,1.5 1.25,1.5 false 2.781,1.417 3.146,1.635 0.365,0.219 10 false SPI+ 1.781,1.417 2.156,1.583 0.375,0.167 10 false SPI- 1.292,1.417 1.781,1.583 0.49,0.167 10 false SPO+ 0.198,1.427 0.667,1.646 0.469,0.219 10 false SPO- 0.167,0.177 0.448,0.417 0.281,0.24 10 false *a
*a Component without harness connected
(Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SPI+) - 5 (SPO+) Always Below 1 Ω
3 (SPI-) - 6 (SPO-) Always Below 1 Ω
2 (SPI+) - 3 (SPI-) Always 10 kΩ or higher
5 (SPO+) - 6 (SPO-) Always 10 kΩ or higher
2 (SPI+) or 5 (SPO+) - Body ground Always 10 kΩ or higher
3 (SPI-) or 6 (SPO-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

16.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Inspect the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION


c.

Check that the malfunction disappears when a new or known good front No. 2 speaker assembly is installed.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG

17.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
a.

Disconnect the F60 stereo component amplifier assembly connector.


b.

Disconnect the G4 and G5 front No. 2 speaker assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F60-13 (TWR+) - G4-4 Always Below 1 Ω
F60-28 (TWR-) - G4-3 Always Below 1 Ω
F60-10 (TWL+) - G5-4 Always Below 1 Ω
F60-25 (TWL-) - G5-3 Always Below 1 Ω
F60-13 (TWR+) or G4-4 - Body ground Always 10 kΩ or higher
F60-28 (TWR-) or G4-3 - Body ground Always 10 kΩ or higher
F60-10 (TWL+) or G5-4 - Body ground Always 10 kΩ or higher
F60-25 (TWL-) or G5-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.INSPECT FRONT NO. 2 SPEAKER ASSEMBLY
a.

Remove the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


b.

Inspect the front No. 2 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION


c.

Check that the malfunction disappears when a new or known good front No. 2 speaker assembly is installed.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG

19.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)
a.

Disconnect the F60 stereo component amplifier assembly connector.


b.

Disconnect the I1 and J1 front No. 1 speaker assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F60-15 (FR+) - I1-1 Always Below 1 Ω
F60-30 (FR-) - I1-2 Always Below 1 Ω
F60-8 (FL+) - J1-1 Always Below 1 Ω
F60-23 (FL-) - J1-2 Always Below 1 Ω
F60-15 (FR+) or I1-1 - Body ground Always 10 kΩ or higher
F60-30 (FR-) or I1-2 - Body ground Always 10 kΩ or higher
F60-8 (FL+) or J1-1 - Body ground Always 10 kΩ or higher
F60-23 (FL-) or J1-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

20.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
a.

Remove the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL


b.

Inspect the front No. 1 speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE FRONT NO. 1 SPEAKER ASSEMBLY

21.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY)
a.

Disconnect the F60 stereo component amplifier assembly connector.


b.

Disconnect the K4 and L5 rear speaker assembly connectors.


c.

Measure the resistance between each of the rear speaker assemblies and the stereo component amplifier assembly to check for an open in the wire harness.

Standard Resistance:
Tester Connection Condition Specified Condition
F60-11 (RR+) - K4-1 Always Below 1 Ω
F60-26 (RR-) - K4-2 Always Below 1 Ω
F60-12 (RL+) - L5-1 Always Below 1 Ω
F60-27 (RL-) - L5-2 Always Below 1 Ω
F60-11 (RR+) or K4-1 - Body ground Always 10 kΩ or higher
F60-26 (RR-) or K4-2 - Body ground Always 10 kΩ or higher
F60-12 (RL+) or L5-1 - Body ground Always 10 kΩ or higher
F60-27 (RL-) or L5-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

22.INSPECT REAR SPEAKER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.INSPECT REAR SPEAKER ASSEMBLY
a.

Remove the rear speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL


b.

Inspect the rear speaker assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION


c.

Check that the malfunction disappears when a new or known good rear speaker assembly is installed.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END

NG