Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2016.08
RM3210E _56 Audio / Visual / Telematics _047511 NAVIGATION / MULTI INFO DISPLAY _0239522 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Mute Signal Circuit between Stereo Component Amplifier and Telematics Transceiver  


DESCRIPTION

The telematics transceiver sends a mute signal to the stereo component amplifier assembly.

The stereo component amplifier assembly controls the volume according to the mute signal from the telematics transceiver.

WIRING DIAGRAM

E336503E21
1.271,1.031 1.885,1.229 0.615,0.198 10 false TMUT 1.729,0.917 2.344,1.115 0.615,0.198 10 false 24 5.292,0.917 5.906,1.115 0.615,0.198 10 false 17 5.531,1.021 6.146,1.219 0.615,0.198 10 false MUTE 0.688,1.917 1.302,2.115 0.615,0.198 10 false F61 0.677,2.083 1.885,2.573 1.208,0.49 10 false Stereo Component Amplifier Assembly 5.104,2.042 7.021,2.333 1.917,0.292 10 false Telematics Transceiver 5.115,1.896 5.729,2.094 0.615,0.198 10 false F36

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>PRECAUTION


PROCEDURE

1.INSPECT TELEMATICS TRANSCEIVER
a.
E259127C33
1.469,0.531 1.906,0.802 0.438,0.271 1.385,1.927 1.021,0.958 false 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 1.563,0.573 1.896,0.771 0.333,0.198 10 false F36 0.688,0.781 1.188,0.99 0.5,0.208 10 false MUTE
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F36-17 (MUTE) - Body ground Power switch on (ACC)
Audio system playing
→ Emergency call mode
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEMATICS TRANSCEIVER)
2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the F61 stereo component amplifier assembly connector.


b.

Disconnect the F36 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F61-24 (TMUT) - F36-17 (MUTE) Always Below 1 Ω
F61-24 (TMUT) or F36-17 (MUTE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Disconnect the F36 telematics transceiver connector.


b.
E176650C26
1.479,0.719 1.969,1.01 0.49,0.292 1.99,2.083 2.167,2.583 false 0.188,0.167 0.354,0.323 0.167,0.156 10 false *a 2.031,2.635 2.458,2.792 0.427,0.156 10 false MUTE 1.604,0.771 1.948,0.969 0.344,0.198 10 false F36
*a Front view of wire harness connector
(Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F36-17 (MUTE) - Body ground Power switch on (ACC) 2.0 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY