Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2016.08
RM3210E _56 Audio / Visual / Telematics _057161 TELEMATICS _0287335 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B15C0  GPS Antenna Disconnected (Short)  B15C1  GPS Antenna Disconnected (Open)  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the roof antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 GPS Antenna Disconnected (Short) Current to the roof antenna assembly is lower than the malfunction threshold for 20 seconds when the power switch is on (IG).
(Short circuit)
·

Telematics transceiver

·

Roof antenna assembly

·

No. 3 antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

Antenna cord sub-assembly (for Antenna Side)

·

Antenna cord sub-assembly (for ECU Side)


B15C1 GPS Antenna Disconnected (Open) Current for roof antenna assembly is higher than the malfunction threshold for 20 seconds when the power switch is on (IG).
(Open circuit)
·

Telematics transceiver

·

Roof antenna assembly

·

No. 3 antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

Antenna cord sub-assembly (for Antenna Side)

·

Antenna cord sub-assembly (for ECU Side)



WIRING DIAGRAM

E342823E09
0.26,1.25 1.896,1.552 1.635,0.302 10 false Roof Antenna Assembly 0.271,1.073 0.427,1.271 0.156,0.198 10 false I 6.073,1.063 6.594,1.26 0.521,0.198 10 false A 6.073,1.24 6.833,1.802 0.76,0.563 10 false Telematics Transceiver 1.875,0.354 2.104,0.604 0.229,0.25 10 false 2 2.281,0.354 2.51,0.604 0.229,0.25 10 false 2 1.156,0.448 1.385,0.698 0.229,0.25 10 false 5 1.375,0.708 1.688,0.906 0.313,0.198 10 false *4 2.75,0.74 3.063,0.938 0.313,0.198 10 false *3 4.219,0.75 4.531,0.948 0.313,0.198 10 false *2 5.646,0.719 5.958,0.917 0.313,0.198 10 false *1 3.313,0.354 3.542,0.604 0.229,0.25 10 false 3 3.719,0.354 3.948,0.604 0.229,0.25 10 false 3 5.188,0.365 5.417,0.615 0.229,0.25 10 false 3 4.781,0.365 5.01,0.615 0.229,0.25 10 false 3 1.865,0.563 2.021,0.76 0.156,0.198 10 false H 2.281,0.563 2.438,0.76 0.156,0.198 10 false G 3.323,0.573 3.479,0.771 0.156,0.198 10 false F 3.719,0.573 3.875,0.771 0.156,0.198 10 false E 4.771,0.563 4.927,0.76 0.156,0.198 10 false D 5.167,0.552 5.729,0.75 0.563,0.198 10 false C 6.125,0.563 6.688,0.76 0.563,0.198 10 false GPS 5.948,0.458 6.177,0.708 0.229,0.25 10 false 1 1.156,2.208 4.979,2.406 3.823,0.198 10 false *1: Antenna Cord Sub-assembly (for ECU Side) 1.156,2.552 4.979,2.75 3.823,0.198 10 false *2: Antenna Cord Sub-assembly (for Antenna Side) 1.156,2.906 4.979,3.104 3.823,0.198 10 false *3: No. 2 Antenna Cord Sub-assembly 1.156,3.26 4.979,3.458 3.823,0.198 10 false *4: No. 3 Antenna Cord Sub-assembly

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG) and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
2.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.

Remove the No. 3 antenna cord sub-assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA CORD>REMOVAL


b.
E271898C19
0.99,0.781 1.344,1.01 0.354,0.229 2.25,1.26 1.865,1.115 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.156,0.823 1.469,1.021 0.313,0.198 10 false I 2.333,1.229 2.646,1.427 0.313,0.198 10 false 5a
*a Component without harness connected
(No. 3 Antenna Cord Sub-assembly)


E215638C34
1.5,0.25 1.917,0.49 0.417,0.24 2.188,1.75 2.188,1.208 false 0.292,0.24 0.604,0.438 0.313,0.198 10 false *a 1.656,0.281 1.813,0.479 0.156,0.198 10 false H 2.115,1.792 2.354,1.958 0.24,0.167 10 false 2a
*a Component without harness connected
(No. 3 Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I-5 - H-2 Always Below 1 Ω
I-5a - H-2a Always Below 1 Ω
I-5 or H-2 - Body ground Always 10 kΩ or higher
I-5a or H-2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY

3.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Remove the No. 2 antenna cord sub-assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL


b.
E215606C94
1.5,0.354 1.896,0.583 0.396,0.229 1.302,1.677 1.302,1.24 false 1.656,0.396 1.813,0.594 0.156,0.198 10 false G 0.188,0.24 0.5,0.438 0.313,0.198 10 false *a 1.229,1.719 1.615,1.938 0.385,0.219 10 false 2a
*a Component without harness connected
(No. 2 Antenna Cord Sub-assembly)


E170183C06
2.385,0.969 2.802,1.219 0.417,0.25 1.719,1.469 1.719,1.76 false 0.083,0.052 0.438,0.354 0.354,0.302 10 false *a 2.552,1.021 2.802,1.271 0.25,0.25 10 false F 1.656,1.792 1.906,2.042 0.25,0.25 10 false 3a
*a Component without harness connected
(No. 2 Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G-2 - F-3 Always Below 1 Ω
G-2a - F-3a Always Below 1 Ω
G-2 or F-3 - Body ground Always 10 kΩ or higher
G-2a or F-3a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Antenna Side)

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

4.INSPECT ANTENNA CORD SUB-ASSEMBLY (for Antenna Side)
a.

Remove the antenna cord sub-assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA CORD>REMOVAL


b.
E170182C06
2.417,1.042 2.833,1.292 0.417,0.25 1.792,1.771 1.792,1.542 false 0.083,0.052 0.26,0.219 0.177,0.167 10 false *a 2.583,1.094 2.74,1.292 0.156,0.198 10 false E 1.74,1.813 2.063,2.063 0.323,0.25 10 false 3a
*a Component without harness connected
(Antenna Cord Sub-assembly)


E215913C19
1.521,0.354 1.885,0.583 0.365,0.229 1.635,1.333 1.635,1.635 false 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.667,0.385 1.823,0.583 0.156,0.198 10 false D 1.542,1.656 1.854,1.854 0.313,0.198 10 false 3a
*a Component without harness connected
(Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-3 - D-3 Always Below 1 Ω
E-3a - D-3a Always Below 1 Ω
E-3 or D-3 - Body ground Always 10 kΩ or higher
E-3a or D-3a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT ANTENNA CORD SUB-ASSEMBLY (for ECU Side)

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (for Antenna Side)

5.INSPECT ANTENNA CORD SUB-ASSEMBLY (for ECU Side)
a.

Remove the No. 5 antenna cord sub-assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA CORD>REMOVAL


b.
E215858C16
1.583,0.313 1.938,0.542 0.354,0.229 1.896,1.646 1.896,1.344 false 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.802,1.667 2.115,1.865 0.313,0.198 10 false 3a 1.719,0.344 1.875,0.542 0.156,0.198 10 false C
*a Component without harness connected
(No. 5 Antenna Cord Sub-assembly)


E258652C20
1.49,0.229 1.906,0.49 0.417,0.26 1.813,1.333 2.177,1.677 true 1.333,1.667 1.698,1.375 true 0.271,0.208 0.583,0.406 0.313,0.198 10 false *a 2.229,1.667 2.542,1.865 0.313,0.198 10 false 1a 1.646,0.271 1.802,0.469 0.156,0.198 10 false A 1.031,1.656 1.49,1.927 0.458,0.271 10 false GPS
*a Component without harness connected
(No. 5 Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-3 - A-1 (GPS) Always Below 1 Ω
C-3a - A-1a Always Below 1 Ω
C-3 or A-1 (GPS) - Body ground Always 10 kΩ or higher
C-3a or A-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE ROOF ANTENNA ASSEMBLY

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY (for ECU Side)

6.REPLACE ROOF ANTENNA ASSEMBLY
a.

Replace the roof antenna assembly with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Clear DTCs
50002 233

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

7.REPLACE TELEMATICS TRANSCEIVER
7.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT