Home › Vehicle Interior › METER / GAUGE / DISPLAY › HEADUP DISPLAY SYSTEM › from 2016.08
RM3210E _58 Vehicle Interior _047509 METER / GAUGE / DISPLAY _0241557 HEADUP DISPLAY SYSTEM C

METER / GAUGE / DISPLAY  HEADUP DISPLAY SYSTEM  B150A  Lost Communication with HMI-LAN  


DESCRIPTION

The combination meter mirror ECU receives signals from the radio and display receiver assembly*1 or navigation receiver assembly*2 via local bus communication and displays audio system and navigation system information on the headup display.

This DTC is stored when the combination meter mirror ECU cannot receive the signal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B150A Lost Communication with HMI-LAN Diagnosis Condition:
·

A registration information signal was received from the Navigation receiver assembly*1 or Radio and display receiver assembly*2 when ACC power source voltage was received by the Navigation receiver assembly*1 or Radio and display receiver assembly*2.

·

The power switch is on (IG).

·

IG power source voltage is 9.5 V or more.


Malfunction Status:

The registration information signal is not received from the Navigation receiver assembly*1 or Radio and display receiver assembly*2.


Malfunction Time:

30 seconds or more


·

Harness or connector

·

Radio and display receiver assembly*1

·

Navigation receiver assembly*2

·

Combination meter mirror ECU


DTC stored for Radio and Display Type or Navigation Receiver Type

*1: for Radio and Display Type

*2: for Navigation Receiver Type


WIRING DIAGRAM

w/ Navigation System


E331962E04
2.396,0.521 2.854,0.719 0.458,0.198 10 false F34 2.396,1.26 2.854,1.458 0.458,0.198 10 false F34 2.802,1.26 3.26,1.458 0.458,0.198 10 false F95 2.802,0.521 3.26,0.719 0.458,0.198 10 false F95 5.083,0.375 5.542,0.573 0.458,0.198 10 false 7 5.073,1.104 5.531,1.302 0.458,0.198 10 false 8 4.844,1.594 5.302,1.792 0.458,0.198 10 false G7 5.26,0.5 5.719,0.698 0.458,0.198 10 false LCL+ 5.271,1.25 5.729,1.448 0.458,0.198 10 false LCL- 1.896,0.521 2.281,0.719 0.385,0.198 10 false CNH1 1.917,1.24 2.323,1.448 0.406,0.208 10 false CNL1 0.948,2.354 3.031,2.625 2.083,0.271 10 false : Local Bus Communication Line 4.844,1.75 6.927,2.021 2.083,0.271 10 false Combination Meter Mirror ECU 2.469,0.323 2.927,0.521 0.458,0.198 10 false 3 2.865,0.323 3.323,0.521 0.458,0.198 10 false 3 2.438,0.719 2.896,0.917 0.458,0.198 10 false *1 2.844,0.719 3.302,0.917 0.458,0.198 10 false *2 2.469,1.052 2.927,1.25 0.458,0.198 10 false 4 2.885,1.052 3.344,1.25 0.458,0.198 10 false 4 2.448,1.458 2.906,1.656 0.458,0.198 10 false *1 2.854,1.458 3.313,1.656 0.458,0.198 10 false *2 3.646,2.104 5.75,2.323 2.104,0.219 10 false *1: for Radio and Display Type 3.635,2.417 5.823,2.594 2.188,0.177 10 false *2: for Navigation Receiver Type 1.031,1.729 3.531,1.917 2.5,0.188 10 false Radio and Display Receiver Assembly*1 1.031,2 3.073,2.208 2.042,0.208 10 false Navigation Receiver Assembly*2


w/o Navigation System


E274272E85
0.865,1.75 3.51,2.083 2.646,0.333 10 false Radio and Display Receiver Assembly 2.25,0.594 2.438,0.76 0.188,0.167 10 false 3 4.927,0.573 5.094,0.74 0.167,0.167 10 false 7 4.708,1.604 5.042,1.854 0.333,0.25 10 false G7 4.719,1.781 6.771,1.979 2.052,0.198 10 false Combination Meter Mirror ECU 0.865,1.583 1.229,1.781 0.365,0.198 10 false F34 1.771,0.688 2.229,0.896 0.458,0.208 10 false CNH1 5.125,0.688 5.583,0.906 0.458,0.219 10 false LCL+ 5.125,1.25 5.573,1.458 0.448,0.208 10 false LCL- 2.25,1.146 2.438,1.323 0.188,0.177 10 false 4 4.927,1.135 5.146,1.333 0.219,0.198 10 false 8 0.948,2.365 3.094,2.635 2.146,0.271 10 false : Local Bus Communication Line 1.781,1.24 2.229,1.417 0.448,0.177 10 false CNL1


PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Navigation System A
w/o Navigation System B



A

2.CHECK FOR DTC

B

5.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check if navigation system DTCs are output.

for Radio and Display Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

for Navigation Receiver Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
Navigation system DTCs are not output. A
Navigation system DTCs are output. B



A

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY OR NAVIGATION RECEIVER ASSEMBLY)

B

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY OR NAVIGATION RECEIVER ASSEMBLY)
a.

Disconnect the G7 combination meter mirror ECU connector.


b.

Disconnect the F34 radio and display receiver assembly*1 or F95 navigation receiver assembly*2 connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-7 (LCL+) - F34-3 (CNH1)*1 Always Below 1 Ω
G7-8 (LCL-) - F34-4 (CNL1)*1 Always Below 1 Ω
G7-7 (LCL+) or F34-3 (CNH1) - Body ground*1 Always 10 kΩ or higher
G7-8 (LCL-) or F34-4 (CNL1) - Body ground*1 Always 10 kΩ or higher
G7-7 (LCL+) - F95-3 (CNH1)*2 Always Below 1 Ω
G7-8 (LCL-) - F95-4 (CNL1)*2 Always Below 1 Ω
G7-7 (LCL+) or F95-3 (CNH1) - Body ground*2 Always 10 kΩ or higher
G7-8 (LCL-) or F95-4 (CNL1) - Body ground*2 Always 10 kΩ or higher


*1: for Radio and Display Type

*2: for Navigation Receiver Type



Result:
Proceed to
OK
NG



OK

4.CHECK FOR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK FOR DTC
a.

Check if meter / gauge system DTCs are output.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
DTC B150A is not output. A
DTC B150A is output (for Radio and Display Type). B
DTC B150A is output (for Navigation Receiver Type). C



A

REPLACE COMBINATION METER MIRROR ECU

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

C

5.CHECK FOR DTC
a.

Check if audio and visual system DTCs are output.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR

Body Electrical > Navigation System > Trouble Codes
50001 212

Result:
Result Proceed to
Audio and visual system DTCs are not output. A
Audio and visual system DTCs are output. B



A

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the G7 combination meter mirror ECU connector.


b.

Disconnect the F34 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G7-7 (LCL+) - F34-3 (CNH1) Always Below 1 Ω
G7-8 (LCL-) - F34-4 (CNL1) Always Below 1 Ω
G7-7 (LCL+) or F34-3 (CNH1) - Body ground Always 10 kΩ or higher
G7-8 (LCL-) or F34-4 (CNL1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK FOR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK FOR DTC
a.

Check if meter / gauge system DTCs are output.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

Body Electrical > Combination Meter > Trouble Codes
50001 122

Result:
Result Proceed to
DTC B150A is not output. A
DTC B150A is output. B



A

REPLACE COMBINATION METER MIRROR ECU

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY