TERMINALS OF ECU
System information · Vehicles built Nov 2005 – Dec 2006
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2008 from Aug 2008
| SKID CONTROL ECU |


| Symbols (Terminal No.) |
Terminal Description |
| GND2 (A26-1) |
Motor ground |
| BM (A26-2) |
Motor relay input |
| FR+ (A26-3) |
Front RH wheel speed sensor power supply |
| FL- (A26-4) |
Front LH wheel speed signal input |
| RR+ (A26-5) |
Rear RH wheel speed signal power supply |
| RL- (A26-6) |
Rear LH wheel speed signal input |
| FSW+ (A26-7)*1 |
Brake pedal load sensing switch input |
| CANH (A26-11) |
CAN communication line H |
| SP1 (A26-12) |
Speed signal output for combination meter |
| MRF (A26-14) |
Fail safe motor relay output |
| MR (A26-15) |
Motor relay output |
| STPO (A26-16) |
Stop light relay output |
| FR- (A26-17) |
Front RH wheel speed signal input |
| FL+ (A26-18) |
Front LH wheel speed sensor power supply |
| RR- (A26-19) |
Rear RH wheel speed signal input |
| RL+ (A26-20) |
Rear LH wheel speed sensor power supply |
| STP2 (A26-21) |
Stop light relay input |
| TS (A26-24) |
Sensor diagnosis check input |
| CANL (A25-25) |
CAN communication line L |
| STP1 (A26-27) |
Stop light switch input |
| HDCS (A26-28)*2 |
Downhill assist control switch input |
| +BS (A26-31) |
Solenoid valve power supply |
| GND1 (A26-32) |
Skid control ECU ground |
| R+ (A26-45) |
Power supply for motor relay |
| IG1 (A26-46) |
ECU power supply |
| LSW (A26-43) |
AUTO LSD switch input |
- HINT:
- *1: w/ 16-inch disc
- *2: w/ Downhill assist control
| CHECK SKID CONTROL ECU |


Disconnect the A26 ECU connector.
Measure the voltage and resistance of the wire harness side connector.
- HINT:
- The voltage cannot be measured with the connector connected to the skid control ECU as the connector is water resistant.
Skid control ECU: Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
GND2 (A26-1) - Body ground
W-B - Body ground
Skid control ECU ground
Always
Below 1 Ω
STP1 (A26-27) - Body ground
L - Body ground
Stop light switch input
Stop light switch OFF
Brake pedal released
Below 1.5 V
STP1 (A26-27) - Body ground
L - Body ground
Stop light switch input
Stop light switch ON
Brake pedal depressed
8 to 16 V
STP2 (A26-21) - Body ground
L - Body ground
Stop light relay input
Stop light switch OFF
Brake pedal released
Below 1.5 V
STP2 (A26-21) - Body ground
L - Body ground
Stop light relay input
Stop light switch ON
Brake pedal depressed
8 to 16 V
STPO (A26-16) - Body ground
W - Body ground
Stop light relay output
Always
10 to 14 V
+BS (A26-31) - Body ground
W - Body ground
Solenoid relay power supply
Always
10 to 14 V
IG1 (A26-46) - Body ground
L - Body ground
ECU power supply
Ignition switch on (IG)
10 to 14 V
HDCS (A26-28)*2
Y - Body ground
Downhill assist control switch input
Downhill assist control switch ON
Below 1 Ω
HDCS (A26-28)*2
Y - Body ground
Downhill assist control switch input
Downhill assist control switch OFF
10 kΩ or higher
FSW+ (A26-7)*1
P - Body ground
Brake pedal load sensing switch input
Brake pedal load sensing switch ON
Brake pedal released
202.4 to 223.7 Ω
FSW+ (A26-7)*1
P - Body ground
Brake pedal load sensing switch input
Brake pedal load sensing switch OFF
Brake pedal released
0,95 to 1.05 kΩ
- HINT:
- *1: w/ 16-inch disc
- *2: w/ Downhill assist control
| CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) |


Disconnect the ID junction block connector.
Measure the resistance of the wire harness side connector.
If the result is not as specified, there may be a malfunction on the wire harness side.Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
PKB (ID-4) - Body ground
B - Body ground
Parking brake switch input
Parking brake switch ON
Below 1 Ω
PKB (ID-4) - Body ground
B - Body ground
Parking brake switch input
Parking brake switch OFF
10 kΩ or higher
Reconnect the ID junction block connector.
Measure the voltage of the wire harness side connector.
Symbols (Terminal No.)
Wiring Color
Terminal Description
Condition
Specified Condition
PKB (ID-4) - Body ground
B - Body ground
Parking brake switch input
Parking brake switch ON
Below 1 V
PKB (ID-4) - Body ground
B - Body ground
Parking brake switch input
Parking brake switch OFF
10 to 14 V
- If the result is not as specified, the junction block (ECU) may be a malfunction.
- If the result is not as specified, the junction block (ECU) may be a malfunction.