2005-2008 RAV4 · Service Manual BRAKE

TERMINALS OF ECU

System information · Vehicles built Jan 2007 – Jul 2008

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2008 from Aug 2008


SKID CONTROL ECU
C110610E03
Symbols (Terminal No.)
Terminal Description
GND2 (A26-1)
Motor ground
BM (A26-2)
Motor relay input
FR+ (A26-3)
Front RH wheel speed sensor power supply
FL- (A26-4)
Front LH wheel speed signal input
RR+ (A26-5)
Rear RH wheel speed signal power supply
RL- (A26-6)
Rear LH wheel speed signal input
FSW+ (A26-7)*1
Brake pedal load sensing switch input
CANH (A26-11)
CAN communication line H
SP1 (A26-12)
Speed signal output for combination meter
MRF (A26-14)
Fail safe motor relay output
MR (A26-15)
Motor relay output
STPO (A26-16)
Stop light relay output
FR- (A26-17)
Front RH wheel speed signal input
FL+ (A26-18)
Front LH wheel speed sensor power supply
RR- (A26-19)
Rear RH wheel speed signal input
RL+ (A26-20)
Rear LH wheel speed sensor power supply
STP2 (A26-21)
Stop light relay input
TS (A26-24)
Sensor diagnosis check input
CANL (A25-25)
CAN communication line L
STP1 (A26-27)
Stop light switch input
HDCS (A26-28)*2
Downhill assist control switch input
+BS (A26-31)
Solenoid valve power supply
GND1 (A26-32)
Skid control ECU ground
R+ (A26-45)
Power supply for motor relay
IG1 (A26-46)
ECU power supply

HINT:
*1: w/ 16-inch disc
*2: w/ Downhill assist control


CHECK SKID CONTROL ECU
F049377E07
  1. Disconnect the A26 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    HINT:
    The voltage cannot be measured with the connector connected to the skid control ECU as the connector is water resistant.

    Skid control ECU: 
    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    GND2 (A26-1) - Body ground
    W-B - Body ground
    Skid control ECU ground
    Always
    Below 1 Ω
    STP1 (A26-27) - Body ground
    L - Body ground
    Stop light switch input
    Stop light switch OFF
    Brake pedal released
    Below 1.5 V
    STP1 (A26-27) - Body ground
    L - Body ground
    Stop light switch input
    Stop light switch ON
    Brake pedal depressed
    8 to 16 V
    STP2 (A26-21) - Body ground
    L - Body ground
    Stop light relay input
    Stop light switch OFF
    Brake pedal released
    Below 1.5 V
    STP2 (A26-21) - Body ground
    L - Body ground
    Stop light relay input
    Stop light switch ON
    Brake pedal depressed
    8 to 16 V
    STPO (A26-16) - Body ground
    W - Body ground
    Stop light relay output
    Always
    10 to 14 V
    +BS (A26-31) - Body ground
    W - Body ground
    Solenoid relay power supply
    Always
    10 to 14 V
    IG1 (A26-46) - Body ground
    L - Body ground
    ECU power supply
    Ignition switch on (IG)
    10 to 14 V
    HDCS (A26-28)*2
    Y - Body ground
    Downhill assist control switch input
    Downhill assist control switch ON
    Below 1 Ω
    HDCS (A26-28)*2
    Y - Body ground
    Downhill assist control switch input
    Downhill assist control switch OFF
    10 kΩ or higher
    FSW+ (A26-7)*1
    P - Body ground
    Brake pedal load sensing switch input
    Brake pedal load sensing switch ON
    Brake pedal released
    202.4 to 223.7 Ω
    FSW+ (A26-7)*1
    P - Body ground
    Brake pedal load sensing switch input
    Brake pedal load sensing switch OFF
    Brake pedal released
    0,95 to 1.05 kΩ

    HINT:
    *1: w/ 16-inch disc
    *2: w/ Downhill assist control

    If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)
C126316E01
  1. Disconnect the ID junction block connector.

  2. Measure the resistance of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    PKB (ID-4) - Body ground
    B - Body ground
    Parking brake switch input
    Parking brake switch ON
    Below 1 Ω
    PKB (ID-4) - Body ground
    B - Body ground
    Parking brake switch input
    Parking brake switch OFF
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the ID junction block connector.

  4. Measure the voltage of the wire harness side connector.

    Symbols (Terminal No.)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    PKB (ID-4) - Body ground
    B - Body ground
    Parking brake switch input
    Parking brake switch ON
    Below 1 V
    PKB (ID-4) - Body ground
    B - Body ground
    Parking brake switch input
    Parking brake switch OFF
    10 to 14 V
    1. If the result is not as specified, the junction block (ECU) may be a malfunction.

← TERMINALS OF ECU (Nov 2005 – Dec 2006)TERMINALS OF ECU (from Aug 2008) →