TERMINALS OF ECU
System information · Vehicles built from Aug 2008
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2008 from Aug 2008
| SKID CONTROL ECU |


| Terminal No. (Symbol) |
Terminal Description |
| 1 (GND1) |
Skid control ECU ground |
| 2 (STP) |
Stop light switch input |
| 4 (RL-) |
Rear LH wheel speed signal input |
| 5 (RL+) |
Rear LH wheel speed sensor power supply |
| 6 (FR-) |
Front RH wheel speed signal input |
| 7 (FR+) |
Front RH wheel speed sensor power supply |
| 11 (SP1) |
Speed signal output for speedometer |
| 12 (+BS) |
Solenoid valve power supply |
| 13 (GND2) |
Motor ground |
| 14 (CANL) |
CAN communication line L |
| 16 (RR-) |
Rear RH wheel speed signal input |
| 17 (RR+) |
Rear RH wheel speed signal power supply |
| 18 (FL-) |
Front LH wheel speed signal input |
| 19 (FL+) |
Front LH wheel speed sensor power supply |
| 22 (STP2) |
Stop light control relay input |
| 24 (BM) |
Motor power supply |
| 25 (CANH) |
CAN communication line H |
| 27 (FSW+)*1 |
Brake pedal load sensing switch input |
| 29 (HDCS)*2 |
Downhill assist control switch input |
| 30 (CSW) |
VSC OFF switch input |
| 31 (STPO) |
Stop light control relay output |
| 33 (TS) |
Sensor diagnosis check input |
| 34 (IG1) |
ECU power supply |
- HINT:
- *1: w/ Booster Failure Compensation
- *2: w/ Downhill Assist Control
| CHECK SKID CONTROL ECU |


Disconnect the A67 ECU connector.
Measure the voltage and resistance of the wire harness side connector.
- HINT:
- The voltage cannot be measured with the connector connected to the skid control ECU as the connector is water resistant.
Skid Control ECU: Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A67-1 (GND1) - Body ground
W-B - Body ground
Skid control ECU ground
Always
Below 1 Ω
A67-2 (STP) - Body ground
L - Body ground
Stop light switch input
Stop light switch off
Brake pedal released
Below 1.5 V
Stop light switch on
Brake pedal depressed
8 to 14 V
A67-12 (+BS) - Body ground
W - Body ground
Solenoid valve power supply
Always
11 to 14 V
A67-13 (GND2) - Body ground
W-B - Body ground
Motor ground
Always
Below 1 Ω
A67-22 (STP2) - Body ground
L - Body ground
Stop light control relay input
Stop light switch off
Brake pedal released
Below 1.5 V
Stop light switch on
Brake pedal depressed
8 to 16 V
A67-24 (BM) - Body ground
B - Body ground
Motor power supply
Always
11 to 14 V
A67-27 (FSW+)*1 - Body ground
P - Body ground
Brake pedal load sensing switch input
Brake pedal load sensing switch on
Brake pedal not depressed beyond the specified point
192 to 234 Ω
Brake pedal load sensing switch off
Brake pedal depressed beyond the specified point
0.9 to 1.1 kΩ
A67-29 (HDCS)*2 - Body ground
Y - Body ground
Downhill assist control switch input
Downhill assist control switch on
Below 1 Ω
Downhill assist control switch off
10 kΩ or higher
A67-30 (CSW) - Body ground
L - Body ground
VSC OFF switch input
VSC OFF switch on
Below 1 Ω
VSC OFF switch off
10 kΩ or higher
A67-31 (STPO) - Body ground
W - Body ground
Stop light control relay output
Ignition switch ON
11 to 14 V
A67-34 (IG1) - Body ground
L - Body ground
ECU power supply
Ignition switch ON
11 to 14 V
- HINT:
- *1: w/ Booster Failure Compensation
- *2: w/ Downhill Assist Control
| CHECK INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU) |


Disconnect the ID junction block connector.
Measure the resistance of the wire harness side connector.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
ID-4 (PKB) - Body ground
B - Body ground
Parking brake switch input
Parking brake switch on
Below 1 Ω
Parking brake switch off
10 kΩ or higher
Reconnect the ID junction block connector.
Measure the voltage of the wire harness side connector.
If the result is not as specified, the junction block (main body ECU) may be a malfunction.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
ID-4 (PKB) - Body ground
B - Body ground
Parking brake switch input
Parking brake switch on
Below 1 V
Parking brake switch off
11 to 14 V