2005-2008 RAV4 · Service Manual ENGINE

Black Smoke Emitted

Circuit diagnosis · Vehicles built from Aug 2007

Versions by build date: Jan 2007 – Jul 2007 from Aug 2007

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing a supply pump, the ECM needs initialization (Click here).
  3. After replacing a injector, the ECM needs registration (Click here).

HINT:
Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List values may occur depending on the measuring conditions or the vehicle's age. Do not assume the vehicle to be normal when the Data List outputs standard values. There may be concealed factors of the malfunction.


1. CHECK OUTPUT DTC (RELATED TO ENGINE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    No output
    A
    DTCs related to the engine
    B



B
REPAIR OR REPLACE ENGINE CONTROL SYSTEM ACCORDING TO DTC OUTPUT
A


2. READ VALUE USING INJECTOR ASSEMBLY (INJECTION VOLUME AND INJECTION FEED BACK VAL #1 TO #4)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

  1. Select the following menu items in order and read the values.

    1. Injection Volume
    2. Injection Feedback Val #1, #2, #3, and #4

    Standard value:
    Item
    Engine Speed*
    Reference Value
    Injection Volume
    Idling (No engine load)
    4.5 to 9.0 mm3
    Injection Feedback Val #1
    Idling (No engine load)
    -3.5 to 3.5 mm3
    Injection Feedback Val #2
    Idling (No engine load)
    -3.5 to 3.5 mm3
    Injection Feedback Val #3
    Idling (No engine load)
    -3.5 to 3.5 mm3
    Injection Feedback Val #4
    Idling (No engine load)
    -3.5 to 3.5 mm3

    HINT:
    *: If no idling conditions are specified, the shift lever should be in the neutral position, and the A/C switch and all accessory switches should be OFF.



NG
Go to step 11
OK


3. PERFORM ENGINE RPM ACCELERATION

HINT:
If the exhaust gas contains excessive black smoke, perform the following operations:

  1. Accelerate the engine speed to the maximum rpm with no load 20 times.

  1. Check the volume of black smoke in the exhaust gas.

    Result:
    Result
    Proceed to
    Black smoke is not present
    OK
    Black smoke remains in the exhaust gas
    NG

    HINT:
    Soot deposits in the exhaust system may cause excessive black smoke.



OK
END
NG


4. CHECK AIR INTAKE SYSTEM AND EXHAUST SYSTEM
  1. Inspect the engine condition (Click here).



NG
CHECK AND REPLACE LOCATIONS WHERE MALFUNCTIONS EXIST
OK


5. CHECK EGR VALVE ASSEMBLY
  1. Check the EGR valve assembly (Click here).



NG
REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
OK


6. CHECK TURBOCHARGING PRESSURE
  1. Check the turbocharger pressure (Click here).

    Standard pressure:
    58.5 to 78.9 kPa (0.60 to 0.80 kgf/cm2, 8.5 to 11.4 psi)



NG
REPLACE TURBOCHARGER SUB-ASSEMBLY
OK


7. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

  1. Select the following menu items in order and read the values.

    1. Fuel Pressure
    2. Injection Volume
    3. Main Injection
    4. Pilot 2 Injection
    5. Injection Feedback Val #1, #2, #3, and #4

    Reference:
    Item
    Engine Speed*
    Reference Value
    Fuel Pressure
    Idling
    38 to 43 MPa
    Fuel Pressure
    2,000 rpm (no engine load)
    61 to 82 MPa
    Fuel Pressure
    3,000 rpm (no engine load)
    74 to 91 MPa
    Injection Volume
    Idling
    3.1 to 7.6 mm3
    Injection Volume
    2,000 rpm (no engine load)
    4.5 to 9.0 mm3
    Injection Volume
    3,000 rpm (no engine load)
    5.5 to 10.0 mm3
    Main Injection
    Idling
    314 to 610 μs
    Pilot 2 Injection
    Idling
    358 to 471 μs
    Injection Feedback Val #1
    Idling
    -3.5 to 3.5 mm3
    Injection Feedback Val #2
    Idling
    -3.5 to 3.5 mm3
    Injection Feedback Val #3
    Idling
    -3.5 to 3.5 mm3
    Injection Feedback Val #4
    Idling
    -3.5 to 3.5 mm3

    HINT:
    If no idling conditions are specified, the shift lever should be in the neutral position, and the A/C switch and all accessory switches should be OFF.


    Result:
    Result
    Proceed to
    Within reference value
    A
    One of Injection Feedback Val #1 to #4 is not within reference value
    B
    Other result
    C



B
REPLACE INJECTOR ASSEMBLY

C
Go to step 11
A


8. CHECK CYLINDER COMPRESSION PRESSURE
  1. Check the cylinder compression pressure (Click here).

    Standard pressure:
    2,700 kPa (27.5 kgf/cm2, 392 psi)

    Minimum pressure:
    2,200 kPa (22.4 kgf/cm2, 319 psi)

    Difference between each cylinder:
    500 kPa (5.1 kgf/cm2, 73 psi)



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


9. CHECK HARNESS AND CONNECTOR (INJECTOR - EDU)

  1. A130528E07
    Disconnect the injector connectors.

  1. Disconnect the EDU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B36-1 - B64-4 (INJ1)
    Below 1 Ω
    B37-1 - B64-2 (INJ2)
    Below 1 Ω
    B38-1 - B64-1 (INJ3)
    Below 1 Ω
    B39-1 - B64-3 (INJ4)
    Below 1 Ω
    B36-2 - B64-5 (COM1)
    Below 1 Ω
    B37-2 - B64-6 (COM2)
    Below 1 Ω
    B38-2 - B64-6 (COM2)
    Below 1 Ω
    B39-2 - B64-5 (COM1)
    Below 1 Ω
    B36-1 or B64-4 (INJ1) - Body ground
    10 kΩ or higher
    B37-1 or B64-2 (INJ2) - Body ground
    10 kΩ or higher
    B38-1 or B64-1 (INJ3) - Body ground
    10 kΩ or higher
    B39-1 or B64-3 (INJ4) - Body ground
    10 kΩ or higher
    B36-2 or B64-5 (COM1) - Body ground
    10 kΩ or higher
    B37-2 or B64-6 (COM2) - Body ground
    10 kΩ or higher
    B38-2 or B64-6 (COM2) - Body ground
    10 kΩ or higher
    B39-2 or B64-5 (COM1) - Body ground
    10 kΩ or higher

  1. Reconnect the injector connectors.

  1. Reconnect the EDU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER FUEL CUT)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1, #2, #3, and #4 Fuel Cut.

  1. Check the engine idling condition while the fuel injection of each cylinder is cut using the tester.

    Result:
    Engine Idling Condition
    Proceed to
    Becomes unstable
    A
    Does not change
    B

    HINT:
    Replace the injector mounted on the cylinder that causes no significant idle speed change.



B
REPLACE INJECTOR ASSEMBLY
A

REPLACE INJECTOR DRIVER

11. READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

    Standard value:
    Between 75 and 95°C (167 and 203°F) with warm engine.



NG
Go to step 17
OK


12. READ VALUE USING INTELLIGENT TESTER (MANIFOLD ABSOLUTE PRESSURE SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.

  1. Read the value.

    Standard value:
    Condition
    MAP Value
    No pressure applied
    Same as atmospheric pressure
    Vacuum applied
    Becomes vacuum
    Pressure applied
    Becomes pressurized



NG
Go to step 18
OK


13. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Read the value.

    Standard value:
    Between 750 to 1,000 rpm with warm engine (A/C switch OFF).



NG
Go to step 19
OK


14. READ VALUE USING INTELLIGENT TESTER (ACCEL POSITION 1 AND 2)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

    Standard voltage:
    Accelerator Pedal
    Accelerator Pedal Condition
    Specified Condition
    Accel Position 1
    Released
    0.6 to 1.0 V
    Accel Position 1
    Depressed
    3.4 to 3.8 V
    Accel Position 2
    Released
    1.4 to 1.8 V
    Accel Position 2
    Depressed
    4.2 to 4.6 V

    HINT:
    In the chart above, "Idling" means that the engine should be idled under the following conditions:
    1. Idle the engine, turn the A/C switch OFF and move the shift lever to N.
    2. After the engine is warmed up, the engine should have no load.



NG
Go to step 20
OK


15. READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Inlet Air.

  1. Read the value.

    OK:
    Same as air temperature near to intake manifold.

    HINT:
    In the chart above, "Idling" means that the engine should be idled under the following conditions:
    1. Idle the engine, turn the A/C switch OFF and move the shift lever to N.
    2. After the engine is warmed up, the engine should have no load.



NG
Go to step 21
OK


16. READ VALUE USING INTELLIGENT TESTER (FUEL PRESSURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

    Standard value:
    38 to 43 MPa engine idling.



NG
Go to step 22
OK

REPLACE ECM

17. INSPECT ENGINE COOLANT TEMPERATURE SENSOR

  1. A081700E11
    Disconnect the engine coolant temperature sensor.

  1. Measure the resistance of the sensor.

    Standard resistance:
    Connection
    Specified Condition
    20°C (68°F)
    2.32 to 2.59 kΩ
    80°C (176°F)
    0.310 to 0.326 kΩ

    NOTICE:
    When checking the ECT sensor in water, keep the terminals dry. After the check, wipe the sensor dry.

    HINT:
    Alternative procedure: Connect an ohmmeter to the installed ECT sensor and read the resistance. Use an infrared thermometer to measure the engine temperature in the immediate vicinity of the sensor. Compare these values against the resistance/ temperature graph. Change the engine temperature (warm up or cool down) and repeat the test.

  1. Reconnect the engine coolant temperature sensor.



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

18. CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

  1. A128588E11
    Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B45-2 (PIM) - B32-117 (PIM)
    Below 1 Ω
    B45-3 (VC) - B32-71 (VCPM)
    Below 1 Ω
    B45-1 (E) - B32-94 (EPIM)
    Below 1 Ω
    B45-2 (PIM) or B32-117 (PIM) - Body ground
    10 kΩ or higher
    B45-3 (VC) or B32-71 (VCPM) - Body ground
    10 kΩ or higher
    B45-1 (E) or B32-94 (EPIM) - Body ground
    10 kΩ or higher

  1. Reconnect the manifold absolute pressure sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

19. INSPECT CRANKSHAFT POSITION SENSOR

  1. A072395E22
    Disconnect the crankshaft position sensor connector.

  1. Measure the resistance of the sensor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B42-1 (NE) - B42-2 (NE-)
    Cold
    835 to 1,400 Ω
    B42-1 (NE) - B42-2 (NE-)
    Hot
    1,060 to 1,645 Ω

    HINT:
    In the table above, the terms "Cold" and "Hot" refer to the temperature of the coils in the sensor. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).

  1. Reconnect the crankshaft position sensor connector.



NG
REPLACE CRANKSHAFT POSITION SENSOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

20. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM)

  1. A128721E04
    Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    A6-1 (VCP2) - A12-56 (VCP2)
    Below 1 Ω
    A6-2 (EPA2) - A12-58 (EPA2)
    Below 1 Ω
    A6-3 (VPA2) - A12-54 (VPA2)
    Below 1 Ω
    A6-4 (VCPA) - A12-55 (VCPA)
    Below 1 Ω
    A6-5 (EPA) - A12-57 (EPA)
    Below 1 Ω
    A6-6 (VPA) - A12-53 (VPA)
    Below 1 Ω
    A6-1 (VCP2) or A12-56 (VCP2) - Body ground
    10 kΩ or higher
    A6-2 (EPA2) or A12-58 (EPA2) - Body ground
    10 kΩ or higher
    A6-3 (VPA2) or A12-54 (VPA2) - Body ground
    10 kΩ or higher
    A6-4 (VCPA) or A12-55 (VCPA) - Body ground
    10 kΩ or higher
    A6-5 (EPA) or A12-57 (EPA) - Body ground
    10 kΩ or higher
    A6-6 (VPA) or A12-53 (VPA) - Body ground
    10 kΩ or higher

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY (ACCELERATOR PEDAL POSITION SENSOR)

21. INSPECT INTAKE AIR TEMPERATURE SENSOR

  1. A098859E05
    Remove the intake air temperature sensor.

  1. Measure the resistance of the sensor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    2.21 to 2.69 kΩ

    NOTICE:
    When checking the sensor in water, keep the terminals dry. After the check, wipe the sensor dry.

  1. Reconnect the intake air temperature sensor.



NG
REPLACE INTAKE AIR TEMPERATURE SENSOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

22. INSPECT COMMON RAIL ASSEMBLY (FUEL PRESSURE SENSOR)

  1. A130311E04
    Disconnect the fuel pressure sensor connector.

  1. Measure the resistance of each terminal of the fuel pressure sensor.

    Standard resistance:
    Tester Connection
    Specified Condition
    B60-2 (PR) - B60-1 (E2)
    16.4 kΩ or less
    B60-2 (PR) - B60-3 (VC)
    3 kΩ or less

  1. Reconnect the fuel pressure sensor connector.



NG
REPLACE COMMON RAIL ASSEMBLY
OK


23. CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

  1. A128588E08
    Disconnect the fuel pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B60-2 (PR) - B32-67 (PCR1)
    Below 1 Ω
    B60-3 (VC) - B32-69 (VCM)
    Below 1 Ω
    B60-1 (E2) - B32-91 (E2M)
    Below 1 Ω
    B60-2 (PR) or B32-67 (PCR1) - Body ground
    10 kΩ or higher
    B60-3 (VC) or B32-69 (VCM) - Body ground
    10 kΩ or higher
    B60-1 (E2) or B32-91 (E2M) - Body ground
    10 kΩ or higher

  1. Reconnect the fuel pressure sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


24. REPLACE ECM
  1. Replace the ECM.

    NOTICE:
    After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

  1. Check the volume of black smoke in the exhaust gas.

    OK:
    Black smoke is not present.



NG
REPLACE SUPPLY PUMP ASSEMBLY
OK

END


← Black Smoke Emitted (Jan 2007 – Jul 2007)Pre-heating Control Circuit (Jan 2007 – Jul 2007) →