DISASSEMBLY
Removal / installation · Vehicles built from Aug 2008
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2008 from Aug 2008
- CAUTION:
- Wear protective gloves. Sharp areas on the front seat frame assembly (w/ adjuster) may injure your hands.
- HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the LH side.
| 1.
REMOVE VERTICAL ADJUSTER COVER LH (for Driver Side) |
 |
- Using a screwdriver, detach the 2 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
| 2.
REMOVE VERTICAL ADJUSTING HANDLE LH (for Driver Side) |
 |
- Remove the 2 screws and handle.
| 3.
REMOVE RECLINING ADJUSTER RELEASE HANDLE LH (for Driver Side) |
 |
- Raise the reclining adjuster release handle to reveal the claw. Using a screwdriver, detach the claw and remove the release handle.
- HINT:
- Tape the screwdriver tip before use.
| 4.
REMOVE RECLINING ADJUSTER RELEASE HANDLE RH (for Front Passenger Side) |
 |
- HINT:
- Use the same procedures described for the driver side.
| 5.
REMOVE FRONT SEAT CUSHION SHIELD LH (for Driver Side) |
 |
- Disconnect the rubber band of the front seatback board or front seatback cover from the front seat frame assembly (w/ adjuster).
- Remove the 2 screws.
Using a screwdriver, detach the 3 claws and remove the cushion shield.
- HINT:
- Tape the screwdriver tip before use.
| 6.
REMOVE FRONT SEAT CUSHION SHIELD RH (for Front Passenger Side) |
 |
- Disconnect the rubber band of the front seatback board or front seatback cover from the front seat frame assembly (w/ adjuster).
- Remove the 2 screws.
Using a screwdriver, detach the 3 claws and remove the cushion shield.
- HINT:
- Tape the screwdriver tip before use.
| 7.
REMOVE FRONT SEAT CUSHION INNER SHIELD LH |
 |
- Remove the screw.
Using a screwdriver, detach the claw and clip. Then remove the inner shield.
- HINT:
- Tape the screwdriver tip before use.
| 8.
REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
|
 |
for Driver Seat:
Disconnect the 2 connectors and detach the 3 clamps.
for Passenger Seat:
Disconnect the 2 connectors and detach the 3 clamps.
- Remove the nut and seat belt.
| 9.
REMOVE FRONT SEAT CUSHION COVER |
 |
Using a clip remover, remove the 2 clips.
Detach the 2 hooks on the front side of the seat cushion.
Using a screwdriver, detach the hooks and remove the seat cushion cover (with pad).
- HINT:
- Tape the screwdriver tip before use.
- Remove the 15 hog rings and seat cushion cover from the seat cushion pad.
| 10.
REMOVE FRONT SEATBACK COVER |
 |
- Open the 2 zippers.
- Lift up the seatback cover and remove the 3 hog rings.
- w/ Active Headrest:
Detach the 4 claws and remove the 2 headrest supports.
- w/o Active Headrest:
Detach the 4 claws and remove the 2 headrest supports.
- w/ Front Seat Side Airbag:
Remove the nut and move the 2 seatback cover brackets.
Remove the seatback cover (with pad) from the front seat frame assembly (w/ adjuster).
- Remove the 11 hog rings and seatback cover from the seatback pad.
| 11.
REMOVE LOWER ACTIVE HEADREST UNIT (w/ Active Headrest) |
 |
Remove the nut.
Detach the clamp.
- Detach the clamp.
Remove the 2 nuts and lower active headrest unit.
| 12.
REMOVE UPPER ACTIVE HEADREST UNIT (w/ Active Headrest) |
 |
Remove the 4 nuts and upper active headrest unit.
| 13.
REMOVE RECLINING ADJUSTER LOWER INSIDE COVER LH |
 |
- Remove the screw.
Detach the claw and remove the inside cover.
| 14.
REMOVE RECLINING ADJUSTER LOWER INSIDE COVER RH |
 |
- HINT:
- Use the same procedures described for the LH side.
| 15.
REMOVE RECLINING ADJUSTER UPPER INSIDE COVER LH |
 |
- Remove the screw and inside cover.
| 16.
REMOVE RECLINING ADJUSTER UPPER INSIDE COVER RH |
 |
Remove the screw and inside cover.
| 17.
REMOVE FRONT SEAT CUSHION LOWER SHIELD LH |
 |
- Using a screwdriver, detach the claw and remove the lower shield.
- HINT:
- Tape the screwdriver tip before use.
| 18.
REMOVE FRONT SEAT CUSHION LOWER SHIELD RH |
 |
- HINT:
- Use the same procedures described for the LH side.
| 19.
REMOVE SEAT POSITION AIRBAG SENSOR (for Driver Side)
|
 |
- Remove the seat slide position sensor protector from the seat position sensor.
Using a T30 "torx" socket, remove the "torx" screw and seat position sensor.
Disconnect the connector.
| 20.
REMOVE FRONT INNER SEAT TRACK ASSEMBLY LH |
 |
Using a T50 "TORX" socket, remove the 2 bolts and inner seat track bracket.
Using a T40 "TORX" socket, remove the 8 bolts and front seat frame assembly (w/ adjuster).


- Using a screwdriver, detach the 2 springs and remove the seat track adjusting handle as shown in the illustration.
| 21.
REMOVE FRONT OUTER SEAT TRACK ASSEMBLY LH |
|