2005-2008 RAV4 · Service Manual BRAKE

C1241 Low Power Supply Voltage Malfunction

Diagnostic trouble codes · Vehicles built from Aug 2008

DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (housed in the actuator assembly) stores this DTC and the fail-safe function prohibits ABS/TRC/VSC operation.
This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or alternator circuit, etc.
The DTC is canceled when the IG1 terminal voltage returns to normal.
DTC Code
DTC Detection Condition
Trouble Area
C1241
Any of the following is detected:
  1. At a vehicle speed of 3 km/h (2 mph) or more, the IG1 terminal voltage is less than 9.5 V for 10 seconds or more.
  2. When the solenoid relay remains on and the IG1 terminal voltage is less than 9.5 V, the relay contact is open for 0.22 seconds or more.
  3. With the IG1 terminal voltage 9.5 V or less, the vehicle speed sensor power supply decreases for 60 seconds or more.
  4. When the motor fail-safe relay is on after the motor relay turns on, the IG1 terminal voltage is 9.5 V or less and the actuator pump drive motor is off for 0.22 seconds or more.
  1. ECU-IG1 fuse
  2. Battery
  3. Charging system
  4. Power source circuit
  5. Internal power supply circuit of the skid control ECU

WIRING DIAGRAM

C194309E02

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. When replacing the brake actuator assembly, perform zero point calibration (Click here).


1. CHECK BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V

    Result:
    Result
    Proceed to
    OK
    A
    NG
    for 2AZ-FE
    B
    for 2GR-FE
    C



B
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (Click here)

C
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (Click here)
A


2. INSPECT SKID CONTROL ECU (IG1 TERMINAL)

  1. C194130E18
    Make sure that there is no looseness in the locking part and connecting part of the connectors.

  1. Disconnect the skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A67-34 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


3. INSPECT SKID CONTROL ECU (GND1 TERMINAL)

  1. C194130E17
    Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A67-1 (GND1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK


4. RECONFIRM DTC
  1. Reconnect the skid control ECU connector.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC (C1241) is not output.
    A
    DTC (C1241) is output.
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)


← C1232/32 Stuck in Deceleration Sensor (+ 7 more codes) (Aug 2007 – Jul 2008)C1241/41 Low Battery Positive Voltage (Nov 2005 – Dec 2006) →