DTC CHECK / CLEAR
Troubleshooting · Vehicles built from Aug 2008
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008 from Aug 2008
| CHECK DTC (When Using Intelligent Tester) |
Turn the ignition switch off and connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Read the DTCs by following the prompts on the intelligent tester screen.
- HINT:
- Refer to the intelligent tester operator manual for further details.
| CLEAR DTC (When Using Intelligent Tester) |
Turn the ignition switch off and connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Operate the intelligent tester to clear the DTCs.
- HINT:
- Refer to the intelligent tester operator manual for further details.
| CHECK DTC (When not Using Intelligent Tester) |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

- SST
- 09843-18040
Turn the ignition switch to ON.
Read DTCs from the ABS warning light and slip indicator light on the combination meter.
- HINT:
- If the ABS warning light and slip indicator light do not blink, perform relevant troubleshooting procedures. The relevant troubleshooting procedures are in the sections listed in the table below.
Trouble Area
See Procedure
ABS warning light circuit
Click here or Click here
Slip indicator light circuit
Click here or Click here
TC and CG terminal circuit
Click here
- As an example, the blinking patterns of the normal system code and DTCs 11 and 21 are shown below.


- If the ABS warning light and slip indicator light do not blink, perform relevant troubleshooting procedures. The relevant troubleshooting procedures are in the sections listed in the table below.
Check the details of the DTCs.
DTC Chart for ABS: ABS Warning Light Display
Intelligent Tester Display
11
C0278
12
C0279
13
C0273
14
C0274
21
C0226
22
C0236
23
C0246
24
C0256
25
C1225
31
C1401
C1405
32
C1402
C1406
33
C1403
C1407
34
C1404
C1408
35
C1413
36
C1414
37
C1337
38
C1415
39
C1416
41
C1241
C1417
43
C1243
44
C1419
C1420
C1442
45
C1245
46
C1421
C1422
C1423
C1424
49
C1425
C1426
51
C1427
C1428
67
C1429
C1430
C1431
91
C1361
94
U0073
95
U0124
97
C1381
DTC Chart for VSC: Slip Indicator Light Display
Intelligent Tester Display
31
C1432
C1433
C1434
32
C1232
34
C1435
C1436
C1443
36
C1210
39
C1336
43 (*1)
-
51
C1201
53
C1203
62
U0123
63
U0126
64
C1380
65
C1437
U0100
66
C1290
C1439
C1445
98
C1440
C1441
- HINT:
- *1: This DTC is output when the VSC system detects a malfunction in the ABS.
After completing the check, disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3, and turn the ignition switch off.
- HINT:
- If 2 or more malfunctions are stored at the same time, the lowest numbered DTC is output first.
| CLEAR DTC (When not Using Intelligent Tester) |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

- SST
- 09843-18040
Turn the ignition switch to ON.
Clear the DTCs stored in the skid control ECU by depressing the brake pedal 8 times or more within 5 seconds.

Check that the ABS warning light and slip indicator light come on.
Remove SST from the terminals of the DLC3.
Turn the ignition switch off.
- HINT:
- Clearing the DTCs cannot be performed by removing the cable from the negative (-) battery terminal or the ECU-IG1 fuse.
| END OF DTC CHECK/CLEAR |
Turn the ignition switch to ON.
Check that the ABS warning light and slip indicator light go off within approximately 3 seconds.
Turn the ignition switch off.