2005-2008 RAV4 · Service Manual ENGINE

B2278 Engine Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jan 2007

DESCRIPTION

This DTC is output when 1) a malfunction is detected between the main body ECU and the engine switch; or 2) either of the switches inside the engine switch is malfunctioning.
DTC No.
DTC Detection Condition
Trouble Area
B2278
Communication is abnormal between main body ECU and engine switch or engine switch is defective
  1. Main body ECU
  2. Engine switch
  3. Wire harness or connector

WIRING DIAGRAM

A165881E01

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (START SWITCH 1 AND 2)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester ON.

  1. Select the following menu items: Body / Main Body ECU / Data List / St SW1 and St SW2.

  1. Read the value displayed on the tester.

    Main body ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    St SW1
    Start Switch 1 / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -
    St SW 2
    Start Switch 2 / ON or OFF
    ON: Engine switch on (IG)
    OFF: Engine switch off
    -

    OK:
    ON appears on the screen.



NG
Go to step 3
OK


2. CHECK SWITCH CONDITION (ENGINE SWITCH)
  1. Ensure the electrical key is inside the cabin.

  1. Check that the power source mode changes as shown below each time the engine switch is pushed.

    OK:
    off → on (ACC) → on (IG) → off



NG
GO TO POWER SOURCE MODE DOES NOT CHANGE
OK

SYSTEM IS OK

3. INSPECT ENGINE SWITCH ASSEMBLY

  1. A109259E05
    Remove the engine switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (SS1) - 5 (GND)
    Pushed
    Below 1 Ω
    2 (SS2) - 5 (GND)
    Pushed
    Below 1 Ω
    7 (SS1) - 5 (GND)
    Not pushed
    10 kΩ or higher
    2 (SS2) - 5 (GND)
    Not pushed
    10 kΩ or higher



NG
REPLACE ENGINE SWITCH ASSEMBLY
OK


4. CHECK WIRE HARNESS (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)

  1. A122232E02
    Disconnect the E31 engine switch connector.

  1. Disconnect the E19 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    E31-7 (SS1) - E19-10 (SSW1)
    Below 1 Ω
    E31-2 (SS2) - E19-9 (SSW2)
    Below 1 Ω
    E31-5 (GND) - Body ground
    Below 1 Ω
    E31-7 (SS1) or E19-10 (SSW1) - Body ground
    10 kΩ or higher
    E31-2 (SS2) or E19-9 (SSW2) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)


← B2277 Detecting Vehicle Submersion (from Jan 2007)B2281 "P" Signal Malfunction (from Jan 2007) →