2005-2008 RAV4 · Service Manual ENGINE

Engine does not Start

Circuit diagnosis · Vehicles built from Jan 2007

DESCRIPTION


ENGINE START SYSTEM OPERATION
  1. When the engine switch is pressed with the brake pedal with the shift lever in P or N depressed, the main body ECU determines that it is an engine start request.

  2. The certification ECU and other ECUs perform key verification via the LIN communication line.

  3. The main body ECU activates the ACC relay.

  4. The main body ECU activates the IG1 and IG2 relays. The engine switch indicator light illuminates in green.

  5. The certification ECU outputs a steering UNLOCK signal. The signal is sent to the steering lock ECU via the main body ECU.

  6. The main body ECU sends an engine start request signal to the ECM.

  7. The ECM sends an ACC cut request signal to the main body ECU.

  8. The ECM and main body ECU activate the ST cut relay.

  9. The main body ECU deactivates the ACC relay until the ECU detects an engine start.

  10. The ECU reactivates the ACC relay and turns off the engine switch indicator light.

    Symbols of main body ECU
    Signals
    SSW1/SSW2
    Engine switch on (ACC, IG) signal
    ACCD
    ACC relay operation signal
    IG2D
    IG2 relay operation signal
    STR2
    ST cut relay operation signal
    STR
    Park / neutral position switch signal
    STP
    Stop light switch signal
    TACH
    Engine start detection signal
    STSW
    Starter activation request signal
    ACCR
    ACC cut request signal

A165895E01

WIRING DIAGRAM

See CRANKING HOLDING FUNCTION CIRCUIT (Click here).

INSPECTION PROCEDURE


1. CHECK WHETHER ENGINE STARTS AFTER STEERING LOCK INITIALIZATION
  1. Open and close the driver door when the engine switch is off.

  1. Check that the engine starts.

    OK:
    Engine starts.

    HINT:
    After the battery runs out, the engine may not start if the steering lock ECU has not been initialized (lock / unlock may not be recorded) through the procedure described above.



OK
SYSTEM OK
NG


2. CHECK WHETHER DTC OUTPUT RECURS
  1. Clear the DTCs.

    HINT:
    After all DTCs are cleared, check if the trouble occurs again 5 seconds after the engine switch is turned on (IG).

  1. Check for DTCs again.

    OK:
    No DTC is output.



NG
GO TO DTC CHART
OK


3. CHECK SWITCH CONDITION
  1. Ensure the electrical key is inside the cabin.

  1. Check that the power source mode changes as shown below each time the engine switch is pushed.

    OK:
    off → on (ACC) → on (IG) → off



NG
GO TO POWER SOURCE MODE DOES NOT CHANGE
OK


4. CHECK BASIC FUNCTION
  1. Ensure there is fuel in the fuel tank and the key is inside the cabin.

  1. Depress the brake pedal with the shift lever in P or N, and keep depressing the pedal.

  1. Check that the engine cranks when the engine switch is pressed.

    OK:
    Engine cranks.



OK
Go to step 8
NG


5. READ VALUE USING INTELLIGENT TESTER (N SW / C SW)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester ON.

  1. Select the following menu items: Body / Main Body ECU / Data List / N SW / C SW.

  1. Read the displays on the tester.

    Main body ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    N SW / C SW
    Park / neutral position switch / ON or OFF
    ON: Shift lever in P or N
    OFF: Shift lever in R or D
    -

    OK:
    When the shift lever is in P or N, ON is displayed on the tester.



NG
REPLACE STOP LIGHT SWITCH
OK


6. CHECK STEERING LOCK SYSTEM
  1. When the engine switch is on (ACC), check that the steering lock can be released.

    OK:
    Steering lock can be released.



NG
GO TO STEERING LOCK SYSTEM
OK


7. INSPECT MAIN BODY ECU

  1. A122230E03
    Disconnect the E20 main body ECU connector.

  1. Depress the brake pedal with the shift lever in P or N, and keep depressing the pedal.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    E20-4 (STSW) - Body ground
    10 to 14 V



NG
GO TO ECD SYSTEM (CRANKING HOLDING FUNCTION CIRCUIT)
OK

REPLACE MAIN BODY ECU

8. READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)
  1. Place the electrical key inside the vehicle.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester ON.

  1. Select the following menu items: Body / Certification ECU / Data List / L Code Chk.

  1. Read the display on the tester.

    Certification ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    L Code Chk
    L Code Check / NG or OK
    NG: L code certification result is abnormal
    OK: L code certification result is normal
    -

    OK:
    L code check result is OK.



NG
GO TO ENGINE IMMOBILISER SYSTEM (STEERING LOCK ECU OR ID CODE BOX MALFUNCTIONS)
OK


9. READ VALUE USING INTELLIGENT TESTER (S CODE CHECK)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester ON.

  1. Select the following menu items: Body / Certification ECU / Data List / S Code Chk.

  1. Read the display on the tester.

    Certification ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    S Code Chk
    S Code Check / NG or OK
    NG: S code certification result is abnormal
    OK: S code certification result is normal
    -

    OK:
    S code check result is OK.



NG
GO TO ENGINE IMMOBILISER SYSTEM (CERTIFICATION ECU OR ID CODE BOX MALFUNCTIONS)
OK


10. READ VALUE USING INTELLIGENT TESTER (ENGINE START REQUEST)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) (do not start the engine) and turn the tester ON.

  1. Select the following menu items: Body / Certification ECU / Data List / Start Req Sig.

  1. Read the displays on the tester.

    Certification ECU 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Start Rqst
    Starter request signal / Yes or No
    YES: ID code box receives immobiliser unset signal
    NO: ID code box does not receive immobiliser unset signal
    -

    OK:
    When ID code box receives immobiliser unset signal, YES is displayed on tester.



NO
REPLACE CERTIFICATION ECU
YES

REPLACE ID CODE BOX


← Power Source Mode does not Change (from Jan 2007)Engine Switch Indicator Circuit (from Jan 2007) →