2005-2008 RAV4 · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007


1. INSTALL INJECTOR ASSEMBLY

NOTICE:
Before installing the injector, check for carbon, foreign matter, etc. on the seal surfaces of the cylinder head and injector. If there is foreign matter, remove it before installing the injector.

  1. Install 4 new nozzle seats to the cylinder head.

  1. A114889E02
    Install new O-rings to each injector.

  1. Apply a light coat of engine oil to the O-rings on each injector.

  1. Install the 4 injectors to the cylinder head.

    NOTICE:
    Fit the injectors to the nozzle seats.

  1. A114890
    Temporarily install the 4 clamps to the cylinder head with the 4 bolts.

  1. Using a hexagon socket wrench, tighten the 4 bolts.

    Torque:
    9 N*m{ 92 kgf*cm , 80 in.*lbf }

  1. A114891E01
    Install the nozzle holder clamps and washers as shown in the illustration.

  1. Temporarily install the nozzle holder clamp bolts.

    NOTICE:
    1. Pay attention to the mounting orientation (beveled edge) of the washer.
    2. When temporarily attaching the nozzle holder clamp and the nozzle holder clamp bolt, be careful not to position them at an angle.

    HINT:
    Apply a light coat of engine oil on the threads of the nozzle holder clamp bolts.

  1. Temporarily install the No. 1, No. 2, No. 3 and No. 4 injection pipe.

  1. Temporarily install 4 new gaskets and the No. 1 leakage pipe with the 4 union bolts.

  1. Tighten the 4 nozzle holder clamp bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


2. INSTALL NO. 1 NOZZLE LEAKAGE PIPE ASSEMBLY

  1. A117983E01
    Temporarily install a new gasket, fuel check valve and bolt.

  1. A110781
    Tighten the 4 union bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. Tighten the fuel check valve and bolt.

    Torque:
    31.5 N*m{ 321 kgf*cm , 23 ft.*lbf } for fuel check valve
    20.5 N*m{ 209 kgf*cm , 15 ft.*lbf } for bolt


3. INSTALL INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. In a case where an injector is replaced, the injection pipes must also be replaced.

  1. A114876E01
    Temporarily install the 4 injection pipes.

  1. Using SST, tighten the 4 nuts at the common rail end of the injection pipes.

    SST
    09023-38401  

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

    HINT:
    1. Use of the proper SST is required to ensure that the correct torque is applied to the injection pipe nut.
    2. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    3. Make sure that the pipe is not deformed or twisted during installation.
      If the pipe is deformed or twisted, or if it cannot be installed properly, replace the pipe with a new pipe.

  1. Using SST, tighten the 4 nuts at the injector end of the injection pipes.

    SST
    09023-38401  

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }

    HINT:
    1. Use of the proper SST is required to ensure that the correct torque is applied to the injection pipe nut.
    2. Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
    3. Make sure that the pipe is not deformed or twisted during installation.
      If the pipe is deformed or twisted, or if it cannot be installed properly, replace the pipe with a new pipe.


4. CONNECT ENGINE WIRE
  1. Connect the engine wire to the engine cover bracket.

  1. Connect the glow plug wire harness.

  1. Install the 2 nuts.

  1. Install the nut and grommet.

    Torque:
    2.2 N*m{ 22 kgf*cm , 19 in.*lbf }

  1. Connect the turbo pressure sensor connector.

  1. Connect the discharge valve connector.

  1. Connect the fuel pressure sensor connector.


5. BLEED AIR FROM FUEL SYSTEM

  1. A130544
    Using the hand pump indicated by the arrows in the illustration, bleed the fuel system. Continue pumping until pumping becomes difficult.


6. INSTALL NO. 1 ENGINE COVER

  1. A123518
    Attach the 4 clips to install the engine cover.


7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

8. PERFORM REGISTRATION OF INJECTOR COMPENSATION CODE

HINT:
Each injector assembly has a characteristic fuel injecting behavior (Click here).


9. CHECK FOR FUEL LEAKS

  1. B127990E01
    Perform the ACTIVE TEST.

    1. Connect the intelligent tester to the DLC3.

    2. Turn the ignition switch on (IG).

    3. Turn the intelligent tester ON.

    4. Enter the following menus: Powertrain / Engine / Active Test.

    5. Perform the Active Test.

      Intelligent Tester Display
      Test Details
      Control Range
      Diagnostic Notes
      Test the Fuel Leak
      Pressurizing common rail internal fuel pressure, and checking for fuel leaks
      Stop/Start
      1. Fuel pressure inside common rail pressurized to specified value and engine speed increased to 2,000 rpm when Start is selected
      2. Above conditions to be maintained while test is Start

← REMOVAL (from Nov 2005)INSTALLATION (from Jan 2007) →