2005-2008 RAV4 · Service Manual BODY

INSPECTION

Inspection · Vehicles built Nov 2005 – Jul 2008

Versions by build date: Nov 2005 – Jul 2008 from Aug 2008


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Retract Mirror)

B131625E01
  1. Disconnect the mirror connector.

  1. Apply battery voltage and check the operation of the mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) →Terminal 3 (MV)
    Battery negative (-) → Terminal 7 (M+)
    Turns upward (A)
    Battery positive (+) → Terminal 7 (M+)
    Battery negative (-) → Terminal 3 (MV)
    Turns downward (B)
    Battery positive (+) → Terminal 6 (MH)
    Battery negative (-) → Terminal 7 (M+)
    Turns left (C)
    Battery positive (+) → Terminal 7 (M+)
    Battery negative (-) → Terminal 6 (MH)
    Turns right (D)

    If the result is not as specified, replace the mirror assembly.

  1. B133548E01
    For each position:
    Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

    OK:
    Measurement Condition
    Mirror Position
    Specified Condition
    Battery positive (+) - Terminal 1 (MR)
    Battery negative (-) - Terminal 2 (MF)
    Forward position A
    Moves from A to retracted position E
    Battery positive (+) - Terminal 2 (MF)
    Battery negative (-) - Terminal 1 (MR)
    Forward position A
    Does not move
    Battery positive (+) - Terminal 1 (MR)
    Battery negative (-) - Terminal 2 (MF)
    Position between forward position A and driving position C
    Moves from B to retracted position E
    Battery positive (+) - Terminal 2 (MF)
    Battery negative (-) - Terminal 1 (MR)
    Position between forward position A and driving position C
    Moves from B to forward position A
    Battery positive (+) - Terminal 1 (MR)
    Battery negative (-) - Terminal 2 (MF)
    Driving position C
    Moves from C to retracted position E
    Battery positive (+) - Terminal 2 (MF)
    Battery negative (-) - Terminal 1 (MR)
    Driving position C
    Does not move
    Battery positive (+) - Terminal 1 (MR)
    Battery negative (-) - Terminal 2 (MF)
    Position between driving position C and retracted position E
    Moves from D to retracted position E
    Battery positive (+) - Terminal 2 (MF)
    Battery negative (-) - Terminal 1 (MR)
    Position between driving position C and retracted position E
    Moves from D to driving position C
    Battery positive (+) - Terminal 1 (MR)
    Battery negative (-) - Terminal 2 (MF)
    Retracted position E
    Does not move
    Battery positive (+) - Terminal 2 (MF)
    Battery negative (-) - Terminal 1 (MR)
    Retracted position E
    Moves from E to driving position C

    NOTICE:
    1. Disconnect and reconnect the battery between each mirror position check.
    2. The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

    If the result is not as specified, replace the mirror assembly.

  1. B133550E03
    w/ Mirror Heater:
    Check the resistance.

    1. Measure the resistance between the terminals.

      Standard resistance:
      Tester connection
      Condition
      Specified Condition
      1 (H-) - 2 (H+)
      65°C (149°F)
      4 to 12 Ω

      If the result is not as specified, replace the outer rear view mirror.

    2. Connect the cable from the negative battery (-) terminal to terminal 5 and the positive battery (+) terminal to terminal 4, then check that the mirror becomes warm.

      OK:
      Mirror becomes warm.

      HINT:
      It takes a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror.


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Retract Mirror)

B133547E01
  1. Disconnect the mirror connector.

  1. Apply battery voltage and check the operation of the mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 3 (MV)
    Battery negative (-) → Terminal 7 (M+)
    Turns upward (A)
    Battery positive (+) → Terminal 7 (M+)
    Battery negative (-) → Terminal 3 (MV)
    Turns downward (B)
    Battery positive (+) → Terminal 6 (MH)
    Battery negative (-) → Terminal 7 (M+)
    Turns left (D)
    Battery positive (+) → Terminal 7 (M+)
    Battery negative (-) → Terminal 6 (MH)
    Turns right (C)

    If the result is not as specified, replace the mirror assembly.

  1. B133549E01
    For each position:
    Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror's movement.

    OK:
    Measurement Condition
    Mirror Position
    Specified Condition
    Battery positive (+) - Terminal 1 (MR)
    Battery negative (-) - Terminal 2 (MF)
    Forward position A
    Moves from A to retracted position E
    Battery positive (+) - Terminal 2 (MF)
    Battery negative (-) - Terminal 1 (MR)
    Forward position A
    Does not move
    Battery positive (+) - Terminal 1 (MR)
    Battery negative (-) - Terminal 2 (MF)
    Position between forward position A and driving position C
    Moves from B to retracted position E
    Battery positive (+) - Terminal 2 (MF)
    Battery negative (-) - Terminal 1 (MR)
    Position between forward position A and driving position C
    Moves from B to forward position A
    Battery positive (+) - Terminal 1 (MR)
    Battery negative (-) - Terminal 2 (MF)
    Driving position C
    Moves from C to retracted position E
    Battery positive (+) - Terminal 2 (MF)
    Battery negative (-) - Terminal 1 (MR)
    Driving position C
    Does not move
    Battery positive (+) - Terminal 1 (MR)
    Battery negative (-) - Terminal 2 (MF)
    Position between driving position C and retracted position E
    Moves from D to retracted position E
    Battery positive (+) - Terminal 2 (MF)
    Battery negative (-) - Terminal 1 (MR)
    Position between driving position C and retracted position E
    Moves from D to driving position C
    Battery positive (+) - Terminal 1 (MR)
    Battery negative (-) - Terminal 2 (MF)
    Retracted position E
    Does not move
    Battery positive (+) - Terminal 2 (MF)
    Battery negative (-) - Terminal 1 (MR)
    Retracted position E
    Moves from E to driving position C

    NOTICE:
    1. Disconnect and reconnect the battery between each mirror position check.
    2. The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

    If the result is not as specified, replace the mirror assembly.

  1. B133551E03
    w/ Mirror Heater:
    Check the resistance.

    1. Using an ohmmeter, measure the resistance between the terminals.

      Standard resistance:
      Tester connection
      Condition
      Specified Condition
      1 (H-) - 2 (H+)
      65°C (149°F)
      4 to 12 Ω

      If the result is not as specified, replace the outer rear view mirror.

    2. Connect the cable from the negative battery (-) terminal to terminal 5 and the positive battery (+) terminal to terminal 4, then check that the mirror becomes warm.

      OK:
      Mirror becomes warm.

      HINT:
      It takes a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror.


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Retract Mirror)

B131625E01
  1. Disconnect the mirror connector.

  1. Apply battery voltage and check the operation of the mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) →Terminal 3 (MV)
    Battery negative (-) → Terminal 7 (M+)
    Turns upward (A)
    Battery positive (+) → Terminal 7 (M+)
    Battery negative (-) → Terminal 3 (MV)
    Turns downward (B)
    Battery positive (+) → Terminal 6 (MH)
    Battery negative (-) → Terminal 7 (M+)
    Turns left (C)
    Battery positive (+) → Terminal 7 (M+)
    Battery negative (-) → Terminal 6 (MH)
    Turns right (D)

    If the result is not as specified, replace the mirror assembly.

  1. B133550E03
    w/ Mirror Heater:
    Check the resistance.

    1. Using an ohmmeter, measure the resistance between the terminals.

      Standard resistance:
      Tester connection
      Condition
      Specified Condition
      1 (H-) - 2 (H+)
      65°C (149°F)
      4 to 12 Ω

      If the result is not as specified, replace the outer rear view mirror.

    2. Connect the cable from the negative battery (-) terminal to terminal 5 and the positive battery (+) terminal to terminal 4, then check that the mirror becomes warm.

      OK:
      Mirror becomes warm.

      HINT:
      It takes a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror.


INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Retract Mirror)

B133547E01
  1. Disconnect the mirror connector.

  1. Apply battery voltage and check the operation of the mirror.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 3 (MV)
    Battery negative (-) → Terminal 7 (M+)
    Turns upward (A)
    Battery positive (+) → Terminal 7 (M+)
    Battery negative (-) → Terminal 3 (MV)
    Turns downward (B)
    Battery positive (+) → Terminal 6 (MH)
    Battery negative (-) → Terminal 7 (M+)
    Turns left (D)
    Battery positive (+) → Terminal 7 (M+)
    Battery negative (-) → Terminal 6 (MH)
    Turns right (C)

    If the result is not as specified, replace the mirror assembly.

  1. B133551E03
    w/ Mirror Heater:
    Check the resistance.

    1. Using an ohmmeter, measure the resistance between the terminals.

      Standard resistance:
      Tester connection
      Condition
      Specified Condition
      1 (H-) - 2 (H+)
      65°C (149°F)
      4 to 12 Ω

      If the result is not as specified, replace the outer rear view mirror.

    2. Connect the cable from the negative battery (-) terminal to terminal 5 and the positive battery (+) terminal to terminal 4, then check that the mirror becomes warm.

      OK:
      Mirror becomes warm.

      HINT:
      It takes a short time for the mirror to become warm.

      If the result is not as specified, replace the outer rear view mirror.

← REMOVAL (from Aug 2008)INSPECTION (from Aug 2008) →