2005-2008 RAV4 · Service Manual ENGINE

P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low

Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007

Also covers:

Versions by build date: Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback. The ECM then regulates the lift amount of the valve in accordance with engine running conditions.
DTC No.
DTC Detection Condition
Trouble Area
P0405
EGR valve position sensor output voltage is less than 0.1 V for more than 5 seconds
(1 trip detection logic)
  1. Open or short in EGR valve position sensor circuit
  2. EGR valve position sensor
  3. ECM
P0406
EGR valve position sensor output voltage is more than 4.9 V for more than 5 seconds
(1 trip detection logic)
  1. Open or short in EGR valve position sensor circuit
  2. EGR valve position sensor
  3. ECM

HINT:
  1. After confirming DTCs P0405 and P0406, check the EGR valve opening angle condition by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / EGR Position.
  2. The result values below are for when the ignition switch is on (IG) (engine is stopped), or when the engine is fully warmed-up and idling.
Result
Condition
Changes between 0.3 V and 4.2 V
Normal
Less than 0.1 V
P0405 (Low input voltage)
More than 4.9 V
P0406 (High input voltage)


MONITOR DESCRIPTION

When output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 0.5 seconds, the ECM interprets this as a malfunction of the sensor circuit, and illuminates the MIL.
G039134E05

WIRING DIAGRAM

Refer to DTC P0400 (Click here).

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. CHECK EGR VALVE POSITION SENSOR POWER SOURCE

  1. A128640E16
    Disconnect the EGR valve position sensor connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    B54-3 (VC) - B54-2 (E2)
    4.5 to 5.5 V

  1. Reconnect the EGR valve position sensor connector.



NG
Go to step 3
OK


2. INSPECT EGR VALVE POSITION SENSOR

  1. A131555E10
    Disconnect the EGR valve position sensor connector.

  1. Measure the resistance of the EGR valve position sensor.

    Standard resistance:
    Tester Connection
    EGR Valve Condition
    Condition
    Specified Condition
    B54-3 (VC) - B54-2 (E2)
    -
    20°C (68°F)
    3.5 to 6.5 kΩ
    B54-4 (EGLS) - B54-2 (E2)
    Fully open
    20°C (68°F)
    3.9 kΩ
    B54-4 (EGLS) - B54-2 (E2)
    Fully closed
    20°C (68°F)
    1.0 kΩ

  1. Reconnect the EGR valve position sensor connector.



NG
REPLACE EGR VALVE
OK


3. CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)

  1. A131548E18
    Disconnect the sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B54-3 (VC) - B32-72 (VCEG)
    Below 1 Ω
    B54-4 (EGLS) - B32-118 (EGLS)
    Below 1 Ω
    B54-2 (E2) - B32-95 (EEGL)
    Below 1 Ω
    B54-3 (VC) or B32-72 (VCEG) - Body ground
    10 kΩ or higher
    B54-4 (EGLS) or B32-118 (EGLS) - Body ground
    10 kΩ or higher

  1. Reconnect the EGR valve position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0400 Exhaust Gas Recirculation Flow (from Aug 2007)P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low (+ P0406) (from Aug 2007) →