2005-2008 RAV4 · Service Manual ENGINE

P0400 Exhaust Gas Recirculation Flow

Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION

The EGR system recirculates exhaust gases, in order to suit every driving condition. The recirculated gas mingles with the intake air, therefore the EGR system can slow combustion speed and keep the combustion temperature down. This helps reduce NOx emissions.
In order to increase EGR circulation efficiency, the ECM adjusts the lift amount of the EGR valve and intake shutter valve angle (throttle valve).
DTC No.
DTC Detection Condition
Trouble Area
P0400
Target and actual positions of the EGR valve is different
(1 trip detection logic)
  1. EGR valve stuck
  2. EGR valve does not move smoothly
  3. Open or short in EGR circuit
  4. Open or short in EGR valve position sensor circuit
  5. EGR valve position sensor
  6. ECM

MONITOR DESCRIPTION

When the target and actual positions of the EGR valve are different, the ECM interprets this as a malfunction of the EGR valve and illuminates the MIL.
C129060E01

WIRING DIAGRAM

A129505E01

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
After warming up the engine, DTC P0400 can be set if 1 second or more passes after quickly accelerating the engine from idling.


1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0400)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0400
    A
    P0400 and P0405 and/or P0406
    B

    HINT:
    If codes other than P0400 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2. READ VALUE USING INTELLIGENT TESTER (EGR POSITION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / EGR Position.

  1. Read the value.

    Result:
    Condition
    Result
    Proceed to
    After warming up the engine, quickly accelerate the engine from idle to 3,000 rpm by using the accelerator pedal
    Constant or changes slowly
    A
    Smooth changes from approximately 0% to approximately 50%
    B

    HINT:
    1. EGR valve closed: EGR Position is 0%
    2. EGR valve open: EGR Position is 65%



B
CHECK FOR INTERMITTENT PROBLEMS
A


3. INSPECT EGR VALVE POSITION SENSOR (RESISTANCE)

  1. A131555E09
    Disconnect the EGR valve position sensor connector.

  1. Measure the resistance of the terminals of the EGR valve position sensor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B54-5 (EGRS) - B54-1 (+B)
    20°C (68°F)
    Approximately 6.5 to 7.5 Ω

  1. Reconnect the EGR valve position sensor connector.



NG
REPLACE EGR VALVE POSITION SENSOR
OK


4. CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)

  1. A131548E16
    Disconnect the EGR valve position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B54-5 (EGRS) - B32-85 (EGRS)
    Below 1 Ω
    B54-5 (EGRS) or B32-85 (EGRS) - Body ground
    10 kΩ or higher

  1. Reconnect the EGR valve position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - INTEGRATION RELAY)

  1. A128461E06
    Disconnect the EGR valve position sensor connector.

  1. Remove the integration relay from the engine room No. 1 relay block.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B54-1 (+B) - 1A-4
    Below 1 Ω
    B54-1 (+B) or 1A-4 - Body ground
    10 kΩ or higher

  1. Reconnect the EGR valve position sensor connector.

  1. Reinstall the integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE EGR VALVE
  1. Replace the EGR valve position sensor (Click here).


NEXT


7. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Clear DTCs (Click here).

  1. Start the engine and drive the vehicle for approximately 15 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0400
    A
    No output
    B



B
SYSTEM IS OK
A

REPLACE ECM


← P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) (from Aug 2007)P0400 Exhaust Gas Recirculation Flow (from Aug 2007) →