P0105 Manifold Absolute Pressure / Barometric Pressure Circuit
Diagnostic trouble codes · Vehicles built from Aug 2007
Also covers:
- P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input
- P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input
Versions by build date: Jan 2007 – Jul 2007 from Aug 2007
DESCRIPTION
The manifold absolute pressure sensor detects the intake manifold pressure by using its built-in sensor unit. The ECM determines the basic injection duration and injection advance timing based on the voltage output by the manifold absolute pressure sensor.

The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa (0 mmHg, 0 in.Hg)). As a result the ECM controls the air-fuel ratio at the proper level under any driving conditions, and fuel control accuracy is not influenced by fluctuations in the atmospheric pressure due to factors such as high altitude, etc.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0105 P0107 P0108 |
Open or short in manifold absolute pressure sensor circuit for 0.8 seconds or more (1 trip detection logic) |
|
- HINT:
- When DTC P0105, P0107, or P0108 is detected, check the intake manifold pressure by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / MAP.
Reference: Intake Manifold Pressure
Malfunction
Approximately 0 kPa
Short in PIM circuit
250 kPa (1,875 mmHg, 73.8 in.Hg) or more
- Open or short in VC circuit
- Open in PIM circuit
- Open in E2 circuit
- Open or short in VC circuit
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.
| 1. READ VALUE USING MANIFOLD ABSOLUTE PRESSURE SENSOR |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.
Read the value.
- OK:
Condition
MAP Value
No pressure applied
Same as atmospheric pressure
Vacuum applied
Becomes vacuum
Pressure applied
Becomes pressurized
|
|
||||
| NG | |
| 2. CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM) |
Disconnect the manifold absolute pressure sensor connector.

Disconnect the ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
B45-2 (PIM) - B32-117 (PIM)
Below 1 Ω
B45-3 (VC) - B32-71 (VCPM)
Below 1 Ω
B45-1 (E) - B32-94 (EPIM)
Below 1 Ω
B45-2 (PIM) or B32-117 (PIM) - Body ground
10 kΩ or higher
B45-3 (VC) or B32-71 (VCPM) - Body ground
10 kΩ or higher
B45-1 (E) or B32-94 (EPIM) - Body ground
10 kΩ or higher
Reconnect the manifold absolute pressure sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 3. CHECK MANIFOLD ABSOLUTE PRESSURE TERMINAL VOLTAGE (VC TERMINAL) |
Disconnect the manifold absolute pressure sensor connector.

Turn the ignition switch on (IG).
Measure the voltage of the manifold absolute pressure sensor.
- Standard voltage:
Tester Connection
Specified Condition
B45-3 (VC) - B45-1 (E)
4.5 to 5.5 V
Reconnect the manifold absolute pressure sensor connector.
|
|
||||
| OK | ||
| ||
| 4. INSPECT TURBOCHARGER SUB-ASSEMBLY |
Check the turbocharger sub-assembly (Click here).
|
|
||||
| OK | |
| 5. INSPECT EGR VALVE ASSEMBLY |
Check the EGR valve assembly (Click here).
|
|
||||
| OK | ||
| ||
