2005-2008 RAV4 · Service Manual ENGINE

P0105 Manifold Absolute Pressure / Barometric Pressure Circuit

Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007

Also covers:

Versions by build date: Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION

The manifold absolute pressure sensor detects the intake manifold pressure by using its built-in sensor unit. The ECM determines the basic injection duration and injection advance timing based on the voltage output by the manifold absolute pressure sensor.
A006532E04
The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa (0 mmHg, 0 in.Hg)). As a result the ECM controls the air-fuel ratio at the proper level under any driving conditions, and fuel control accuracy is not influenced by fluctuations in the atmospheric pressure due to factors such as high altitude, etc.
DTC No.
DTC Detection Condition
Trouble Area
P0105
P0107
P0108
Open or short in manifold absolute pressure sensor circuit for 0.8 seconds or more
(1 trip detection logic)
  1. Open or short in manifold absolute pressure sensor circuit
  2. Manifold absolute pressure sensor
  3. Turbocharger sub-assembly
  4. EGR valve assembly
  5. ECM

HINT:
When DTC P0105, P0107, or P0108 is detected, check the intake manifold pressure by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / MAP.
Reference: 
Intake Manifold Pressure
Malfunction
Approximately 0 kPa
Short in PIM circuit
250 kPa (1,875 mmHg, 73.8 in.Hg) or more
  1. Open or short in VC circuit
  2. Open in PIM circuit
  3. Open in E2 circuit


WIRING DIAGRAM

C128771E01

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
If DTCs relating to different systems are output, and they share terminal E2 as their ground, check this ground circuit first.


1. READ VALUE USING MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.

  1. Read the value.

    OK:
    Condition
    MAP Value
    No pressure applied
    Same as atmospheric pressure
    Vacuum applied
    Becomes vacuum
    Pressure applied
    Becomes pressurized



OK
Go to step 4
NG


2. CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

  1. A128588E11
    Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B45-2 (PIM) - B32-117 (PIM)
    Below 1 Ω
    B45-3 (VC) - B32-71 (VCPM)
    Below 1 Ω
    B45-1 (E) - B32-94 (EPIM)
    Below 1 Ω
    B45-2 (PIM) or B32-117 (PIM) - Body ground
    10 kΩ or higher
    B45-3 (VC) or B32-71 (VCPM) - Body ground
    10 kΩ or higher
    B45-1 (E) or B32-94 (EPIM) - Body ground
    10 kΩ or higher

  1. Reconnect the manifold absolute pressure sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK MANIFOLD ABSOLUTE PRESSURE TERMINAL VOLTAGE (VC TERMINAL)

  1. A128633E03
    Disconnect the manifold absolute pressure sensor connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage of the manifold absolute pressure sensor.

    Standard voltage:
    Tester Connection
    Specified Condition
    B45-3 (VC) - B45-1 (E)
    4.5 to 5.5 V

  1. Reconnect the manifold absolute pressure sensor connector.



NG
REPLACE ECM
OK

REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

4. INSPECT TURBOCHARGER SUB-ASSEMBLY
  1. Check the turbocharger sub-assembly (Click here).



NG
REPLACE TURBOCHARGER SUB-ASSEMBLY
OK


5. INSPECT EGR VALVE ASSEMBLY
  1. Check the EGR valve assembly (Click here).



NG
REPLACE EGR VALVE ASSEMBLY
OK

REPLACE ECM


← P0101 Mass or Volume Air Flow Circuit Range / Performance Problem (from Jan 2007)P0105 Manifold Absolute Pressure / Barometric Pressure Circuit (+ P0107, P0108) (from Aug 2007) →