P0234 Turbocharger / Supercharger Overboost Condition
Diagnostic trouble codes · Vehicles built from Aug 2007
Also covers:
- P0299 Turbocharger / Supercharger Underboost
- P1251 Turbocharger / Supercharger Overboost Condition (Too High)
Versions by build date: Jan 2007 – Jul 2007 from Aug 2007
DESCRIPTION
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0234 |
Turbocharging pressure is higher than the threshold for 60 seconds. (1 trip detection logic) |
|
| P0299 |
Turbocharging pressure is lower than the threshold for 40 seconds when the turbocharging pressure deviates from the requirement. (2 trip detection logic) |
|
| P1251 |
Turbocharging pressure is higher than the requirement for 0.5 seconds. (1 trip detection logic) |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
| 1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0234, P0299 AND/OR P1251) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
- Result:
Display (DTC Output)
Proceed to
P0234, P0299 and/or P1251
A
P0234, P0299 and/or P1251 and other DTCs
B
|
|
||||
| A | |
| 2. CHECK CONNECTION OF VACUUM HOSE |
- HINT:
- Check the vacuum hoses of turbocharger system connections.
|
|
||||
| OK | |
| 3. CHECK VACUUM (TURBOCHARGER - VACUUM REGULATING VALVE) |
Using a three-way connector, connect a vacuum gauge to the hose between the VRV and turbocharger.
Warm up the engine coolant temperature to above 75°C (167°F).
Check the vacuum at the engine speed of 900 rpm.
- Result:
Vacuum
Proceed to
0 kPa (0 mmHg, 0 in.Hg) to 50 kPa (375 mmHg, 14.8 in.Hg)
A
Above 50 kPa (375 mmHg, 14.8 in.Hg)
B
|
|
||||
| A | |
| 4. INSPECT VACUUM REGULATING VALVE (RESISTANCE) |
Measure the vacuum regulating valve resistance (Click here).
- Standard resistance:
- 11.1 to 12.5 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (VACUUM REGULATING VALVE - ECM) |
Disconnect the vacuum regulating valve (VRV) connector.

Disconnect the ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance:
Tester Connection
Specified Condition
B32-84 (VN) - B44-2
Below 1 Ω
B32-84 (VN) or B44-2 - Body ground
10 kΩ or higher
Reconnect the vacuum regulating valve connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 6. INSPECT TURBOCHARGER SUB-ASSEMBLY |
Check the turbocharger sub-assembly (Click here).
|
|
||||
| OK | |
| 7. INSPECT EGR VALVE ASSEMBLY |
Check the EGR valve assembly (Click here).
|
|
||||
| OK | |
| 8. READ VALUE USING MANIFOLD ABSOLUTE PRESSURE SENSOR |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.
Read the value.
- OK:
Condition
MAP Value
No pressure applied
Same as atmospheric pressure
Vacuum applied
Becomes vacuum
Pressure applied
Becomes pressurized
|
|
||||
| OK | ||
| ||
