2005-2008 RAV4 · Service Manual ENGINE

P0234 Turbocharger / Supercharger Overboost Condition

Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007

Also covers:

Versions by build date: Jan 2007 – Jul 2007 from Aug 2007

DESCRIPTION

DTC No.
DTC Detection Condition
Trouble Area
P0234
Turbocharging pressure is higher than the threshold for 60 seconds.
(1 trip detection logic)
  1. Vacuum regulating valve for turbocharger control
  2. Open or short in vacuum regulating valve circuit
  3. Turbocharger
  4. Vacuum hose
  5. EGR valve
  6. ECM
P0299
Turbocharging pressure is lower than the threshold for 40 seconds when the turbocharging pressure deviates from the requirement.
(2 trip detection logic)
P1251
Turbocharging pressure is higher than the requirement for 0.5 seconds.
(1 trip detection logic)

WIRING DIAGRAM

C128773E02

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0234, P0299 AND/OR P1251)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0234, P0299 and/or P1251
    A
    P0234, P0299 and/or P1251 and other DTCs
    B



B
GO TO DTC CHART
A


2. CHECK CONNECTION OF VACUUM HOSE

HINT:
Check the vacuum hoses of turbocharger system connections.



NG
REPAIR OR REPLACE VACUUM HOSE
OK


3. CHECK VACUUM (TURBOCHARGER - VACUUM REGULATING VALVE)
  1. Using a three-way connector, connect a vacuum gauge to the hose between the VRV and turbocharger.

  1. Warm up the engine coolant temperature to above 75°C (167°F).

  1. Check the vacuum at the engine speed of 900 rpm.

    Result:
    Vacuum
    Proceed to
    0 kPa (0 mmHg, 0 in.Hg) to 50 kPa (375 mmHg, 14.8 in.Hg)
    A
    Above 50 kPa (375 mmHg, 14.8 in.Hg)
    B



B
Go to step 6
A


4. INSPECT VACUUM REGULATING VALVE (RESISTANCE)
  1. Measure the vacuum regulating valve resistance (Click here).

    Standard resistance:
    11.1 to 12.5 Ω



NG
REPLACE VACUUM REGULATING VALVE
OK


5. CHECK HARNESS AND CONNECTOR (VACUUM REGULATING VALVE - ECM)

  1. A128655E04
    Disconnect the vacuum regulating valve (VRV) connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B32-84 (VN) - B44-2
    Below 1 Ω
    B32-84 (VN) or B44-2 - Body ground
    10 kΩ or higher

  1. Reconnect the vacuum regulating valve connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT TURBOCHARGER SUB-ASSEMBLY
  1. Check the turbocharger sub-assembly (Click here).



NG
REPLACE TURBOCHARGER SUB-ASSEMBLY
OK


7. INSPECT EGR VALVE ASSEMBLY
  1. Check the EGR valve assembly (Click here).



NG
REPLACE EGR VALVE ASSEMBLY
OK


8. READ VALUE USING MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.

  1. Read the value.

    OK:
    Condition
    MAP Value
    No pressure applied
    Same as atmospheric pressure
    Vacuum applied
    Becomes vacuum
    Pressure applied
    Becomes pressurized



NG
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
OK

REPLACE ECM


← P0200 Injector Circuit / Open (from Aug 2007)P0234 Turbocharger / Supercharger Overboost Condition (+ P0299, P1251) (from Aug 2007) →