2005-2008 RAV4 · Service Manual ENGINE

P0088 Fuel Rail / System Pressure - Too High

Diagnostic trouble codes · Vehicles built from Jan 2007

Also covers:

Versions by build date: Nov 2005 – Dec 2006 from Jan 2007

DESCRIPTION

DTC No.
DTC Detection Condition
Trouble Area
P0088
Internal fuel pressure of common rail is too high:
Fuel pressure exceeds 200 MPa (2,039 kgf/cm2, 29,007 psi)
(1 trip detection logic)
  1. Supply pump (suction control valve)
  2. Common rail assembly (pressure discharge valve)
  3. Short in supply pump (suction control valve) circuit
  4. ECM
P1229
Fuel over-feed:
Internal fuel pressure continues exceeding target fuel pressure despite ECM closing suction control valve
(1 trip detection logic)
  1. Short in supply pump (suction control valve) circuit
  2. Supply pump (suction control valve)
  3. ECM

HINT:
  1. DTC P0088 and P1229 can be detected if the vehicle is driven at 50 km/h (31 mph) for 5 minutes.
  2. For more information on the supply pump (suction control valve) and common rail system, refer to the system description (Click here).
  3. When DTC P0088 and/or P1229 is set, check the internal fuel pressure of the common rail by entering the following menus on the intelligent tester: Powertrain / Engine and ECT / Data List / Fuel Press.
Reference: 
Engine Speed
Fuel Pressure
Idling
Approximately 37 to 43 MPa
3,000 rpm (No engine load)
Approximately 60 to 66 MPa


MONITOR DESCRIPTION

  1. P0088 (Internal fuel pressure too high):
    The ECM sets this DTC if the fuel pressure inside the common rail is more than 200 MPa (2,039 kgf/cm2, 29,007 psi). This DTC indicates that: 1) the suction control valve may be stuck open or 2) there may be a short in the suction control valve circuit.
    If this DTC is set, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned off.
  1. P1229 (Fuel over-feed):
    The ECM sets this DTC if the actual fuel pressure inside the common rail remains higher than the target fuel pressure, despite the ECM closing the suction control valve. This DTC indicates that the suction control valve may be stuck open, or there may be a short in its circuit. Under this condition, the pressure discharge valve operates frequently.
    If this DTC is set, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned off.

MONITOR STRATEGY

P0088: 
Required sensor
Fuel pressure sensor
Frequency of operation
Continuous
Duration
1 second
MIL operation
1 driving cycle
P1229: 
Required sensor
Fuel pressure sensor
Frequency of operation
Continuous
Duration
10 minutes
MIL operation
1 driving cycle

TYPICAL ENABLING CONDITIONS

P0088: 
Specification
The monitor will not run if the fuel pressure sensor or suction control valve circuit is malfunctioning.
P1229: 
Item
Specification
Target fuel pressure variation
Small
The monitor will not run if the fuel pressure sensor or suction control valve circuit is malfunctioning.

TYPICAL MALFUNCTION THRESHOLDS

P0088: 
Detection Criteria
Threshold
Fuel pressure sensor
200 MPa (2,039 kgf/cm2, 29,007 psi) or more
P1229: 
Detection Criteria
Threshold
The internal fuel pressure of the common rail when the suction control valve is closed.
Remains higher than target fuel pressure

WIRING DIAGRAM

C128799E01

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing a supply pump, the ECM needs initialization (Click here).


1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0088 AND/OR P1229)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0088 and/or P1229
    A
    P0190, P0192 and/or P0193
    B



B
GO TO DTC CHART
A


2. INSPECT SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

  1. A113717E02
    Disconnect the B46 suction control valve connector.

  1. Measure the resistance of the suction control valve.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B46-1 - B46-2
    20°C (68°F)
    1.9 to 2.3 Ω

  1. Reconnect the suction control valve connector.



NG
REPLACE SUPPLY PUMP ASSEMBLY
OK


3. CHECK IF DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Clear DTCs (Click here).

  1. Disconnect the suction control valve connector and then start the engine. Wait for 1 minute.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    No output or engine does not start
    A
    P1229
    B

  1. Reconnect the suction control valve connector.



B
REPLACE SUPPLY PUMP ASSEMBLY
A


4. CHECK WIRE HARNESS (SCV - ECM)

  1. A128632E01
    Disconnect the B46 valve connector.

  1. Disconnect the B32 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    B46-1 - B32-42 (PCV+)
    Below 1 Ω
    B46-2 - B32-41 (PCV-)
    Below 1 Ω
    B46-1 or B32-42 (PCV+) - Body ground
    10 kΩ or higher
    B46-2 or B32-41 (PCV-) - Body ground
    10 kΩ or higher

  1. Reconnect the suction control valve connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


5. REPLACE COMMON RAIL ASSEMBLY
  1. Replace the common rail assembly.


NEXT


6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Clear DTCs (Click here).

  1. Start the engine and drive the vehicle for approximately 15 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0088 and/or P1229
    A
    No output
    B



B
SYSTEM IS OK
A

REPLACE ECM


← P0088 Fuel Rail / System Pressure - Too High (+ P1229) (Nov 2005 – Dec 2006)P0093 Fuel System Leak Detected - Large Leak (Nov 2005 – Dec 2006) →