2005-2008 RAV4 · Service Manual ENGINE

P1386 Injector for Exhaust Fuel Addition

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

A114032E03
The exhaust fuel addition injector is mounted on the exhaust port of the cylinder head, and low pressure is provided to the injector by the feed pump in the supply pump. This injector adds fuel by a control signal from the ECM.
This injector is used for two different controls: DPNR catalyst regeneration and nitrogen oxides (NOx) reduction.
Under the DPNR catalyst regeneration control, the injector adds fuel to raise a catalyst temperature.
In the other control, the injector helps the air-fuel ratio become RICH. As a result, NOx in the exhaust gas will be reduced in response to the RICH air-fuel ratio.

HINT:
  1. For more information on the exhaust fuel addition injector and TOYOTA D-CAT*1, refer to the following procedures (Click here).
  2. If P1386 is present, refer to the diagnostic trouble code (DTC) chart for TOYOTA D-CAT (Click here).
  3. "Learning value" represents a correction learning value of the fuel addition volume to raise the DPNR*2 catalyst temperature to a target range.
*1: Diesel Clean Advanced Technology
*2: Diesel Particulate-NOx Reduction system

DTC No.
DTC Detection Condition
Main Trouble Area
Related Trouble Area
P1386
Excess or low fuel addition volume from exhaust fuel addition injector:
Air-fuel ratio deviates from a value estimated by ECM while the injector is adding fuel
(1 trip detection logic)
  1. Open or short in exhaust fuel addition injector circuit
  2. Exhaust fuel addition injector
  3. DPNR catalytic converter (Manifold converter sub-assembly)
  1. Open in exhaust temperature sensor circuit
  2. A/F sensor
  3. Exhaust gas temperature sensor
  4. Supply pump assembly
  5. Mass air flow meter
  6. Fuel leaks in exhaust fuel addition injector
  7. Main injector
  8. Cylinder compression pressure
  9. Valve clearance
  10. Valve timing
  11. Blockage in air intake system
  12. Leakage in air intake system
  13. Blockage in exhaust system
  14. Leakage in exhaust system
  15. Blockage in EGR system
  16. Leakage in EGR system
  17. ECM
Low fuel addition volume from exhaust fuel addition injector:
Learning value*3 exceeds standard level
(1 trip detection logic)
Exhaust fuel addition injector nozzle stuck open:
Air-fuel ratio becomes RICHER than standard level, or exhaust gas temperature becomes higher than standard level
(1 trip detection logic)
*3: Correction learning value of the fuel addition volume to raise the DPNR catalyst temperature to a target range.

HINT:
  1. DTC P2047, P2048 or P2049 will be present if there is an open malfunction in the exhaust fuel addition injector circuit.
  2. If any one of the main injectors has a closed valve malfunction, rough idle will result. Compensatory injection volume learning values of each cylinder can be read by using the intelligent tester. When the value is more than 3.0 mm3, the cylinder is malfunctioning.
  3. Usually compensation injection volume is 3.0 mm3 or less.


MONITOR DESCRIPTION

HINT:
"Learning value" represents a correction learning value of the fuel addition volume to raise the DPNR*4 catalyst temperature to a target range.
*4: Diesel Particulate-NOx Reduction system.

In order to detect malfunctions in the exhaust fuel addition injector, the ECM monitors the air-fuel ratio, DPNR catalytic temperature and learning value.
  1. When the exhaust fuel addition injector adds fuel during NOx reduction, the ECM monitors the air-fuel ratio when the exhaust fuel addition injector adds fuel. If the air-fuel ratio is too RICH or too LEAN against the ECM predetermined air-fuel ratio, the ECM determines that the fuel addition volume is small or large, and illuminates the MIL. For this malfunction, there is no fail-safe operation.
  2. The ECM always monitors the DPNR catalytic converter temperature and the air-fuel ratio. When the temperature becomes higher than its usual level or the air-fuel ratio becomes extremely RICH, the ECM judges that the injector is stuck open and illuminates the MIL. If this malfunction occurs, the ECM enters the fail-safe mode to limit the acceptable vehicle speed to approximately 80 km/h (50 mph) by limiting the engine power.
  3. During DPNR catalyst regeneration, the ECM monitors the learning value. Normally, the learning value for the DPNR catalyst regeneration is in the vicinity of 1.0. Thus if the learning value is at 1.99 or more for a certain period of time, the ECM judges the fuel addition volume from the injector is insufficient and illuminates the MIL. If this malfunction occurs, the ECM enters the fail-safe mode to limit the acceptable vehicle speed to approximately 80 km/h (50 mph) by limiting the engine power.
Malfunction Condition by Fail-Safe Operation: 
Fail-Safe Operation
Malfunction Condition
Malfunction Detection Condition
Drive Pattern
No fail-safe operation
Low or excess fuel addition volume from the exhaust fuel addition injector
When the exhaust fuel addition injector adds fuel during NOx reduction, if actual air-fuel ratio deviates from a value estimated by the ECM when the exhaust fuel addition injector adds fuel
After warming up the engine perform DPNR REJU (PM) in the ACTIVE TEST menu using the intelligent tester, and drive at constant vehicle speed within 50 to 100 km/h (31 to 62 mph) for more than 15 minutes
Limits engine power to maximum vehicle speed of approximately 80 km/h (50 mph)
Exhaust fuel addition injector is stuck open
DPNR catalytic converter temperature becomes higher than 800°C (1,472°F) or air-fuel ratio is less than approximately 12,0: 1 for a couple of seconds
Idling engine for more than 5 minutes*5
Limits engine power to maximum vehicle speed of approximately 80 km/h (50 mph)

HINT:
DPNR catalyst regeneration is prohibited

Low fuel addition volume from the exhaust fuel addition injector
During DPNR catalyst regeneration, when learning value of 1.99 or more continues for a certain period of time*6
After warming up the engine perform DPNR REJU (PM) in the ACTIVE TEST menu using the intelligent tester, and drive at constant vehicle speed within 50 to 100 km/h (31 to 62 mph) for more than 30 minutes
*5: The DPNR catalytic converter temperature will not reach 800°C (1,472°F) or higher during idle even if the exhaust fuel addition injector is stuck open.
*6: While the DPNR catalyst regeneration is performed, the ECM raises the DPNR catalytic converter temperature to more than 600°C (1,112°F) by adding fuel using the exhaust fuel addition injector. If the temperature does not reach 600 °C (1,112 °F) during the attempt, the correction learning value of the fuel addition volume increases by increments in order to raise the DPNR catalytic converter temperature to the target range.
A128653E01

WIRING DIAGRAM

C128636E02

INSPECTION PROCEDURE

HINT:
"Learning value" used in here represents a correction learning value of the fuel addition volume to raise the DPNR catalyst temperature to a target range.


1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P1386)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P1386
    A
    P1386 and other DTCs
    B

    HINT:
    If codes other than P1386 are output, perform troubleshooting for those DTCs first.



B
GO TO DTC CHART
A


2. CHECK FAIL-SAFE CONDITION
  1. Check the condition of fail-safe operation while the MIL is being illuminated.

    Result:
    Condition of Fail-Safe Operation
    Proceed to
    Limits vehicle speed to approximately 80 km/h (50 mph)
    A
    No fail-safe operation
    B



B
Go to step 7
A


3. READ VALUE USING EXHAUST GAS TEMPERATURE SENSOR
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON. (Do not start the engine.)

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Initial Exhaust Temp (In) and Initial Exhaust Temp (Out).

  1. Read the value.

    Result:
    Temperature Displayed
    Proceed to
    OK (Same value as actual exhaust gas temperature)
    A
    1,000°C (1,832°F)
    B

    HINT:
    If there is an open circuit, the tester indicates 1,000°C (1,832°F).



B
GO TO DTC P0544, P0545, P0546, P2301, P2302, AND P2033 (RELATED TO EXHAUST GAS TEMPERATURE SENSOR)
A


4. PERFORM ENGINE RPM ACCELERATION (WHITE SMOKE AND FUEL ODOR)

CAUTION:
Stop the engine immediately if there is white smoke or fuel odors during the below inspection. Fuel may be leaking from the exhaust fuel addition injector.

  1. Remove the cable from the negative (-) battery terminal for 1 minute, and then reconnect the cable.

  1. After the engine starts, promptly accelerate the engine to approximately 3,000 rpm with no load 3 times.

  1. Check for white smoke in exhaust gases.

  1. Check for a fuel odors in exhaust gases.

    Result:
    Result
    Proceed to
    Either white smoke or fuel odors in exhaust gases
    A
    Other than above
    B



A
Go to step 17
B


5. READ VALUE USING A/F RATIO

CAUTION:
Stop the engine immediately if there is white smoke or fuel odors during the below inspection. Fuel may be leaking from the exhaust fuel addition injector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

  1. Read the air-fuel ratio displayed on the tester after idling the engine for 3 minutes.

    Result:
    A/F Ratio
    Proceed to
    More than 12
    A
    Less than 12
    B



B
Go to step 17
A


6. READ VALUE USING EXHAUST GAS TEMPERATURE SENSOR

CAUTION:
Stop the engine immediately if there is white smoke or fuel odors during the below inspection. Fuel may be leaking from the exhaust fuel addition injector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Initial Exhaust Temp (In) and Initial Exhaust Temp (Out).

  1. Check that exhaust gas temperature is within the specification below.

    OK:
    Condition
    Exhaust Gas Temperature
    Idling after warming up engine
    Constant at approximately 50 to 700°C (122 to 1,292°F)



NG
GO TO DTC P0544, P0545, P0546, P2301, P2302, AND P2033 (RELATED TO EXHAUST GAS TEMPERATURE SENSOR)
OK


7. READ VALUE USING A/F RATIO
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List.

  1. After warming up the engine, check if the air-fuel ratio varies when accelerating the engine from idling to 3,000 rpm by fully depressing the accelerator pedal 3 times.

    Result:
    Air-fuel Ratio
    Proceed to
    Varies
    OK
    Not varies once
    NG



NG
GO TO DTC P2237, P2238, AND P2239 (RELATED TO A/F SENSOR)
OK


8. INSPECT EXHAUST FUEL ADDITION INJECTOR

  1. A128635E01
    Disconnect the B52 exhaust fuel addition injector connector.

  1. Measure the resistance of the terminals of the exhaust fuel addition injector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B52-1 - B52-2
    20°C (68°F)
    6.8 to 8.2 Ω

  1. Reconnect the exhaust fuel addition injector connector.



NG
REPLACE EXHAUST FUEL ADDITION INJECTOR
OK


9. CHECK WIRE HARNESS (EXHAUST FUEL ADDITION INJECTOR - ECM)

  1. A129658E01
    Disconnect the B52 exhaust fuel addition injector connector.

  1. Disconnect the B32 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E52-1 - B32-105 (FIV)
    Below 1 Ω
    E52-2 - B32-109 (E1)
    Below 1 Ω
    E52-1 or B32-105 (FIV) - Body ground
    10 kΩ or higher

  1. Reconnect the exhaust fuel addition injector connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


10. CHECK FOR FUEL LEAKAGE (IN EXHAUST FUEL ADDITION INJECTOR)
  1. Visually check if there is a fuel leak between the supply pump and exhaust fuel addition injector.

    HINT:
    1. Primary pressure of a maximum of 1 MPa (10 kgf/cm2, 145 psi) is provided from a feed pump inside the supply pump to the exhaust fuel addition injector.
    2. Fuel leaks are possible inside the components (supply pump, etc).



NG
REPAIR OR REPLACE FUEL LEAKAGE POINT
OK


11. READ VALUE USING INJECTION VOLUME (COMPENSATION OF INJECTION VOLUME)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Value.

  1. Read the value.

    Result:
    Result
    Proceed to
    Compensatory injection volume is more than 3.0 mm3
    A
    Compensatory injection volume is 3.0 mm3 or less
    B

    HINT:
    Usually compensation injection volume is 3.0 mm3 or less.



B
Go to step 13
A


12. CHECK ENGINE COMPONENT PARTS
  1. Check that there is no abnormality in the main injector, cylinder compression pressure, valve timing, and valve clearance.

  1. Check that there is no leakage or blockage in the air intake, exhaust, and EGR systems.



NG
REPAIR OR REPLACE MALFUNCTIONING PART
OK


13. INSPECT EXHAUST FUEL ADDITION INJECTOR (INJECTION VOLUME)

  1. A094588E02
    Remove the exhaust fuel addition injector (Click here).

  1. Using SST, attach the exhaust fuel addition injector to a nozzle tester.

SST
09268-41047   (95336-08070)
09268-45014   (09268-41220)
09268-41150  
  1. Apply a pressure of 0.29 MPa (3.0 kgf/cm2, 42 psi) to the nozzle tester.

  1. Connect SST (wire) to the exhaust fuel addition injector.

SST
09842-30080  
  1. Inspect the injector.

    OK:
    Condition
    Result
    Leave the injector undisturbed for 1 minute with fuel pressurized
    No leakage from the injector
    Apply battery voltage to the injector
    Fuel is emitted from the injector

    HINT:
    1. Injection volume after leaving the exhaust fuel addition injector for 10 seconds with the pressurized fuel applied is as follows:

      Reference:
      25 cm3 (1.5 cu.in.)

    2. The above is a reference value. Your reading may differ from this value depending on the measuring conditions, etc.
    3. Check that the nozzle of the exhaust fuel addition injector is not clogged.

  1. Reinstall the exhaust fuel addition injector.



NG
REPLACE EXHAUST FUEL ADDITION INJECTOR
OK


14. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DPNR CATALYST REGENERATION)
  1. Clear the learning value by removing the cable from the negative (-) battery terminal for more than 1 minute.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the DPNR Rejuvenate (PM).

  1. After warming up the engine, drive the vehicle at a constant speed within 50 to 100 km/h (31 to 62 mph) (with smooth throttle operations) for more than 15 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / AFS FT B1 S1, Initial Exhaust Temp (In), Initial Exhaust Temp (Out) and Exhaust Fuel Addition FB.

  1. Check the exhaust gas temperatures (Initial Exhaust Temp (In) and (Out)) and the learning value (Exhaust Fuel Addition FB).

    Result:
    Result
    Proceed to
    Exhaust gas temperature does not become higher than 600°C (1,112°F)
    A
    Exhaust gas temperature becomes higher than 600°C (1,112°F), and the learning value remains in the vicinity of 1.0
    B



B
CHECK FOR INTERMITTENT PROBLEMS
A


15. REPLACE EXHAUST FUEL ADDITION INJECTOR
  1. Replace the exhaust fuel addition injector (Click here).


NEXT


16. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DPNR CATALYST REGENERATION)
  1. Clear the learning value by removing the cable from the negative (-) battery terminal for more than 1 minute.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the DPNR Rejuvenate (PM).

  1. After warming up the engine, drive the vehicle at a constant speed within 50 to 100 km/h (31 to 62 mph) (with smooth throttle operations) for more than 15 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / AFS FT B1 S1, Initial Exhaust Temp (In), Initial Exhaust Temp (Out) and Exhaust Fuel Addition FB.

  1. Check the exhaust gas temperatures (Initial Exhaust Temp (In) and (Out)) and the learning value (Exhaust Fuel Addition FB).

    Result:
    Result
    Proceed to
    Exhaust gas temperature does not become higher than 600°C (1,112°F)
    A
    Exhaust gas temperature becomes higher than 600°C (1,112°F), and the learning value remains in the vicinity of 1.0
    B



B
END
A

REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

17. INSPECT EXHAUST FUEL ADDITION INJECTOR (INJECTION VOLUME)

  1. A094588E02
    Remove the exhaust fuel addition injector (Click here).

  1. Using SST, attach the exhaust fuel addition injector to a nozzle tester.

SST
09268-41047   (95336-08070)
09268-45014   (09268-41220)
09268-41150  
  1. Apply a pressure of 0.29 MPa (3.0 kgf/cm2, 42 psi) to the nozzle tester.

  1. Connect SST (wire) to the exhaust fuel addition injector.

SST
09842-30080  
  1. Inspect the injector.

    OK:
    Condition
    Result
    Leave the injector undisturbed for 1 minute with fuel pressurized
    No leakage from the injector
    Apply battery voltage to the injector
    Fuel is emitted from the injector

    HINT:
    1. Injection volume after leaving the exhaust fuel addition injector for 10 seconds with the pressurized fuel applied as follows:

      Reference:
      25 cm3 (1.5 cu.in.)

    2. The above is a reference value. Your reading may differ from this value depending on the measuring conditions, etc.
    3. Check that the nozzle of the exhaust fuel addition injector is not clogged.

  1. Reinstall the exhaust fuel addition injector.



NG
REPLACE EXHAUST FUEL ADDITION INJECTOR
OK

GO TO DTC P1238 (RELATED MAIN INJECTOR)


← P1271 Fuel Regulator Circuit Malfunction (EDU Drive) (+ P1272) (from Jan 2007)P1425 Differential Pressure Sensor Circuit (+ P1427, P1428) (from Nov 2005) →