2005-2008 RAV4 · Service Manual SUSPENSION & AXLE

C2111/11 Transmitter ID1 Operation Stop

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

The tire pressure warning valve and transmitter that is installed in the tires and wheels measures the air pressure of the tires. The measured values are transmitted to the tire pressure warning antenna on the body as radio waves and then sent to the tire pressure warning ECU and receiver. The ECU compares the measured air pressure values with the air pressure threshold. When the measured air pressure values are less than this threshold, the warning light in the combination meter turns on.
The tire pressure warning ECU and receiver stores a DTC when the tire pressure warning valve and transmitter stops transmitting signals. At this time, forcibly transmit the signals by releasing the tire pressure rapidly. The stored DTC is cleared when the signal transmission is resumed.
DTC No
DTC Detection Condition
Trouble Area
C2111/11
C2112/12
C2113/13
C2114/14
Tire pressure warning valve and transmitter stops transmitting signals
  1. Tire pressure warning valve and transmitter
  1. Tire pressure warning ECU and receiver

HINT:
It is necessary to perform the procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.


WIRING DIAGRAM

F101027E05

INSPECTION PROCEDURE

NOTICE:
It is necessary to register an ID code after replacing the tire wheel and/or the tire pressure warning ECU and receiver (Click here).


1. PERFORM FORCED TRANSMISSION OF TRANSMITTER ID OF ALL WHEELS
  1. Set the pressure of each tire to the specified value.

    Standard pressure:
    220 kPa (2.2 kgf/cm2, 32 psi)

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Select tirepress by following the prompts displayed on the intelligent tester.

    Tire pressure warning ECU and receiver:
    Item
    Measurement item / Range (Display)
    Normal Condition
    Diagnostic Note
    Tirepress1
    ID1 tire pressure / min.: 0 kPa (0 kgf/cm2, 0 psi), max.: 637.5 kPa (6.48 kgf/cm2, 92.2 psi)
    Actual tire pressure
    -
    Tirepress2
    ID2 tire pressure / min.: 0 kPa (0 kgf/cm2, 0 psi), max.: 637.5 kPa (6.48 kgf/cm2, 92.2 psi)
    Actual tire pressure
    -
    Tirepress3
    ID3 tire pressure / min.: 0 kPa (0 kgf/cm2, 0 psi), max.: 637.5 kPa (6.48 kgf/cm2, 92.2 psi)
    Actual tire pressure
    -
    Tirepress4
    ID4 tire pressure / min.: 0 kPa (0 kgf/cm2, 0 psi), max.: 637.5 kPa (6.48 kgf/cm2, 92.2 psi)
    Actual tire pressure
    -

  1. Rapidly release the pressure from each wheel by approximately 40 kPa (0.4 kgf/cm2, 5.8 psi) for 30 seconds or more.

    1. Check that the tire pressure data displayed on the intelligent tester screen changes.

      OK:
      The tire pressure data displayed on the intelligent tester screen changes with the value of the tire pressure.

      NOTICE:
      1. It may take up to 1 minute to display the updated tire pressure data.
      2. When the tirepress data (IDs 1 to 4) changes, reset the tire pressure of the tires to the specified value, rotate the tires 90 to 270° and recheck.

    2. After confirming that the tire pressure data displayed on the intelligent tester screen has changed, set the pressure of each tire to the specified value.

      Standard pressure:
      220 kPa (2.2 kgf/cm2, 32 psi)

      HINT:
      If the tire pressure data displayed on the intelligent tester screen has not changed after rechecking, go to the troubleshooting procedures of DTCs C2121/21 to C2124/24 which indicate transmission or reception malfunctions (Click here).



NG
CHECK OTHER PROBLEM (MALFUNCTION IN TRANSMISSION OR RECEPTION FUNCTION)
OK

END


← DIAGNOSTIC TROUBLE CODE CHART (from Nov 2005)C2121/21 No Signal from Transmitter ID1 in Main Mode (+ 7 more codes) (from Nov 2005) →