2005-2008 RAV4 · Service Manual SUSPENSION & AXLE

C2165/65 Abnormal Temperature Inside ID1 Tire

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

The tire pressure warning valve and transmitter measures tire internal temperature as well as tire pressure, and transmits the information to the tire pressure monitor antenna along with the transmitter ID. If the measured temperature is out of the specified range, the tire pressure warning ECU and receiver recognizes it as a malfunction, outputs DTCs, and blinks the tire pressure warning light.
DTC No.
DTC Detection Condition
Trouble Area
C2165/65
C2166/66
C2167/67
C2168/68
Tire internal temperature is outside -40 to 120°C (-40 to 419°F)
  1. Tire
  2. Tire pressure warning valve and transmitter

HINT:
It is necessary to perform the procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.


INSPECTION PROCEDURE

NOTICE:
It is necessary to register an ID code after replacing the tire wheel and/or the tire pressure warning ECU and receiver (Click here).


1. IDENTIFY TRANSMITTER (CORRESPONDING TO DTC)
  1. Set the pressure of each tire to the specified value.

    Standard pressure:
    220 kPa (2.2 kgf/cm2, 32 psi)

  1. Connect the intelligent tester to the DLC3.

  1. Select tirepress by following the prompts displayed on the intelligent tester.

    Tire pressure warning ECU and receiver:
    Item
    Measurement item / Range (Display)
    Normal Condition
    Diagnostic Note
    Tirepress1
    ID1 tire pressure / min.: 0 kPa (0 kgf/cm2, 0 psi), max.: 637.5 kPa (6.48 kgf/cm2, 92.2 psi)
    Actual tire pressure
    -
    Tirepress2
    ID2 tire pressure / min.: 0 kPa (0 kgf/cm2, 0 psi), max.: 637.5 kPa (6.48 kgf/cm2, 92.2 psi)
    Actual tire pressure
    -
    Tirepress3
    ID3 tire pressure / min.: 0 kPa (0 kgf/cm2, 0 psi), max.: 637.5 kPa (6.48 kgf/cm2, 92.2 psi)
    Actual tire pressure
    -
    Tirepress4
    ID4 tire pressure / min.: 0 kPa (0 kgf/cm2, 0 psi), max.: 637.5 kPa (6.48 kgf/cm2, 92.2 psi)
    Actual tire pressure
    -

  1. Rapidly release the tire pressure from any tire by 40 kPa (0.4 kgf/cm2, 5.8 psi) for 30 seconds or more.

    HINT:
    1. Identify the malfunctioning tire pressure warning valve and transmitter by rapidly releasing the pressure from each tire.
    2. Record which tirepress data (ID1 to ID4) corresponds to each tire.


    Result:
    Condition
    Detection Condition
    One of tirepress data (ID1 to ID4) changed
    Normal
    No tirepress data changed
    Transmitter corresponding to DTC

NOTICE:
  1. It may take up to 1 minute to display the updated data.
  2. When the tirepress data (IDs 1 to 4) changes, reset the tire pressure of the tires to the specified value, rotate the tires 90 to 270° and recheck.
  3. When the transmitter is normal, record the tire location and the transmitter ID.

  1. When one of the tirepress data (IDs 1 to 4) changes, repeat the same procedure on the rest of the tires (one by one) to identify which tire pressure warning valve and transmitter the DTC corresponds to.

  1. When the tirepress data (IDs 1 to 4) has been changed, identify the malfunctioning tire pressure warning valve and transmitter by using recorded ID numbers and the output DTC.

  1. Set the pressure of each tire to the specified value.

    Standard pressure:
    220 kPa (2.2 kgf/cm2, 32 psi)


NEXT

REPLACE TIRE WHEEL (TIRE PRESSURE WARNING VALVE AND TRANSMITTER)


← C2141/41 Transmitter ID1 Error (+ C2142/42, C2143/43, C2144/44) (from Nov 2005)C2171/71 Transmitter ID not Registered in Main Mode (from Nov 2005) →