2005-2008 RAV4 · Service Manual SUSPENSION & AXLE

C2141/41 Transmitter ID1 Error

Diagnostic trouble codes · Vehicles built from Nov 2005

Also covers:

DESCRIPTION

DTC No.
DTC Detection Condition
Trouble Area
C2141/41
C2142/42
C2143/43
C2144/44
If an "ERROR" signal is received 3 times consecutively, tire pressure warning valve and transmitter will be judged as defective and this DTC will be output.
This will happen in situations where inflation pressure is outside range 0 to 537.5 kPa (0 to 5.27 kgf/cm2, 0 psi to 77.7 psi), temperature inside tire is outside specified range -40 to 215°C (-40 to 419 °F), or an error occurs in tire pressure warning valve and transmitter.
Tire pressure warning valve and transmitter

HINT:
It is necessary to perform the procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.


INSPECTION PROCEDURE

NOTICE:
It is necessary to register an ID code after replacing the tire wheel and/or the tire pressure warning ECU and receiver (Click here).


1. IDENTIFY TRANSMITTER (CORRESPONDING TO DTC)
  1. Set the pressure of each tire to the specified value.

    Standard pressure:
    220 kPa (2.2 kgf /cm2, 32 psi)

  1. Connect the intelligent tester to the DLC3.

  1. Select tirepres by following the prompts displayed on the intelligent tester.

    Tire pressure warning ECU and receiver:
    Item
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    Tirepress1
    ID1 tire pressure/ minimum: 0 kPa (0 kgf/cm2, 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2, 92.5 psi)
    Actual tire pressure
    -
    Tirepress2
    ID2 tire pressure/ minimum: 0 kPa (0 kgf/cm2, 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2, 92.5 psi)
    Actual tire pressure
    -
    Tirepress3
    ID3 tire pressure/ minimum: 0 kPa (0 kgf/cm2, 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2, 92.5 psi)
    Actual tire pressure
    -
    Tirepress4
    ID4 tire pressure/ minimum: 0 kPa (0 kgf/cm2, 0 psi) maximum: 637.5 kPa (6.5 kgf/cm2, 92.5 psi)
    Actual tire pressure
    -

    NOTICE:
    It may take up to 1 minute to display the updated data.

  1. Rapidly release the tire pressure from any tire by 40 kPa (0.4 kgf/cm2, 5.8 psi) for 30 seconds or more.

    HINT:
    1. Identify the malfunctioning tire pressure warning valve and transmitter by rapidly releasing the pressure from each tire.
    2. Record which tirepress data (ID1 to ID4) corresponds to each tire.

  1. Check the Data List.

    Result:
    Condition
    Detection Condition
    One of tirepress data (ID1 to ID4) changed
    Normal
    None of tirepress data changed
    Transmitter corresponding to DTC

    NOTICE:
    1. When the tirepress data (IDs 1 to 4) changes, reset the tire pressure of the tires to the specified value, rotate the tires 90 to 270° and recheck.
    2. When the transmitter is normal, record the tire location and the transmitter ID.

  1. When one of the tirepress data (IDs 1 to 4) changes, repeat the same procedure on the rest of the tires (one by one) to identify which tire pressure warning valve and transmitter the DTC corresponds to.

  1. When the tirepress data (IDs 1 to 4) has been changed, identify the malfunctioning tire pressure warning valve and transmitter by using recorded ID numbers and the output DTC.

  1. Set the pressure of each tire to the specified value.

    Standard pressure:
    220 kPa (2.2 kgf /cm2, 32 psi)


NEXT

REPLACE TIRE WHEEL (TIRE PRESSURE WARNING VALVE AND TRANSMITTER)


← C2121/21 No Signal from Transmitter ID1 in Main Mode (+ 7 more codes) (from Nov 2005)C2165/65 Abnormal Temperature Inside ID1 Tire (+ C2166/66, C2167/67, C2168/68) (from Nov 2005) →