INSTALLATION
Removal / installation · Vehicles built from Aug 2007
Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007
| 1.
INSTALL TURBOCHARGER SUB-ASSEMBLY |
 |
- Install a new gasket and the turbocharger with the 3 nuts.
-
Torque:
- 60 N*m{
612 kgf*cm
, 44 ft.*lbf
}
| 2.
INSTALL TURBOCHARGER STAY |
 |
- Install the turbocharger stay with the 2 nuts and 2 spacers.
-
Torque:
- 36 N*m{
370 kgf*cm
, 26 ft.*lbf
}
- NOTICE:
- Do not reuse the turbo stay.
| 3.
INSTALL NO. 2 TURBO OIL PIPE |
 |
- Install 2 new gaskets and the turbo oil pipe with the 2 bolts.
-
Torque:
- 35 N*m{
357 kgf*cm
, 26 ft.*lbf
}
| 4.
INSTALL EGR COOLER ASSEMBLY
|
 |
Install 2 new gaskets and a new O-ring to the EGR cooler.
- Temporarily install the EGR cooler with the 2 bolts and 2 nuts.
Temporarily install the 4 bolts.
- Tighten the 2 bolts and 2 nuts holding the EGR cooler to the cylinder block.
-
Torque:
- 10 N*m{
102 kgf*cm
, 7 ft.*lbf
}
- Tighten the 2 bolts holding the EGR cooler to the exhaust manifold.
-
Torque:
- 16 N*m{
163 kgf*cm
, 12 ft.*lbf
}
- Tighten the 2 bolts holding the EGR cooler to the cylinder head.
-
Torque:
- 24 N*m{
245 kgf*cm
, 18 ft.*lbf
}
| 5.
INSTALL TURBO OIL OUTLET PIPE |
 |
- Install 2 new gaskets and the oil pipe with the 4 bolts.
-
Torque:
- 11 N*m{
112 kgf*cm
, 8 ft.*lbf
}
| 6.
INSTALL NO. 5 WATER BY-PASS PIPE |
 |
- Using needle-nose pliers, grip the claws of the clip and slide the clip to install the No. 2 and No. 3 water by-pass hoses.
- Install the pipe with the 2 bolts.
-
Torque:
- 28 N*m{
285 kgf*cm
, 21 ft.*lbf
}
| 7.
INSTALL NO. 1 TURBO INSULATOR |
 |
- Install the insulator with the 2 bolts.
-
Torque:
- 20.5 N*m{
209 kgf*cm
, 15 ft.*lbf
}
| 8.
INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
|
 |
- Temporarily install a new gasket and the exhaust manifold converter with the 3 nuts.
- Temporarily install the No. 2 exhaust manifold stay with the nut and 2 bolts.
- Temporarily install the No. 2 manifold stay with the 3 bolts.
- Temporarily install the No. 1 manifold stay with the bolt and nut.
- Tighten the 2 bolts holding the No. 2 exhaust manifold stay to the cylinder block (upper bolt → lower bolt).
-
Torque:
- 56 N*m{
571 kgf*cm
, 41 ft.*lbf
}
- While tightening the manifold converter towards turbocharger, tighten the 3 nuts holding the exhaust manifold converter to the turbocharger.
-
Torque:
- 25 N*m{
255 kgf*cm
, 18 ft.*lbf
}
- Tighten the nut holding the No. 2 exhaust manifold stay to the exhaust manifold converter.
-
Torque:
- 56 N*m{
571 kgf*cm
, 41 ft.*lbf
}
- Tighten the bolt holding the No. 2 manifold stay to the exhaust manifold converter.
-
Torque:
- 56 N*m{
571 kgf*cm
, 41 ft.*lbf
}
- HINT:
- Ensure that the stay is pushed flush to the cylinder block and manifold converter while tightening.
- Tighten the 2 bolts holding the No. 2 manifold stay to the cylinder block.
-
Torque:
- 56 N*m{
571 kgf*cm
, 41 ft.*lbf
}
- Tighten the bolt holding the No. 1 manifold stay to the cylinder head.
-
Torque:
- 25 N*m{
255 kgf*cm
, 18 ft.*lbf
}
- HINT:
- Ensure that the stay is pushed flush to the cylinder head and manifold converter while tightening.
- Tighten the nut holding the No. 1 manifold stay to the exhaust manifold converter.
-
Torque:
- 25 N*m{
255 kgf*cm
, 18 ft.*lbf
}
| 9.
INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR
|
 |
- Install the manifold converter insulator with the 4 bolts.
-
Torque:
- 28.5 N*m{
291 kgf*cm
, 21 ft.*lbf
}
| 10.
INSTALL ENGINE ASSEMBLY |
 |
Install the engine to the vehicle (Click here).