2005-2008 RAV4 · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. DISCHARGE FUEL SYSTEM PRESSURE procedures must be performed before disconnecting any part of the fuel system.
  2. After performing the DISCHARGE FUEL SYSTEM PRESSURE procedures, pressure will remain in the fuel line. When disconnecting the fuel line, place a cloth or equivalent over fittings to reduce the risk of fuel spray.

  1. Remove the console box (Click here).

  1. A128750E01
    Disconnect the connector.

  1. Start the engine. After the engine has stopped, turn the ignition switch off.

    HINT:
    DTC P0171 (system too lean) may be set.

  1. Check that the engine does not start.

  1. Remove the fuel tank cap, and let the air out of the fuel tank.

  1. A128750E01
    Connect the connector.

  1. Install the console box (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


3. REMOVE RADIATOR SUPPORT OPENING COVER

4. REMOVE FRONT WHEEL RH

5. REMOVE NO. 1 ENGINE UNDER COVER

6. REMOVE FRONT FENDER APRON RH

7. REMOVE NO. 1 ENGINE COVER

  1. A112206
    Remove the 2 nuts and cover.


8. DRAIN ENGINE COOLANT
  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator reservoir cap.

    CAUTION:
    Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the cylinder block drain cock plug.

    A112179E01


9. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug and drain the oil into a container.


10. REMOVE AIR CLEANER CAP

  1. A124559
    Disconnect the mass air flow meter connector.

  1. Disconnect the purge VSV connector.

  1. Disconnect the 4 wire harness clamps.

  1. A124560
    Disconnect the No. 2 ventilation hose from the air cleaner hose.

  1. Disconnect the purge line hose from the clamp.

  1. A124561
    Lock the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.

  1. A124562
    Unfasten the 2 hook clamps, and then remove the air cleaner cap.

  1. Remove the air cleaner filter element from the air cleaner case.


11. REMOVE THROTTLE BODY

  1. A124564
    Disconnect the purge line hose from the throttle body.

  1. Disconnect the water by-pass hose from the throttle body.

  1. Disconnect the No. 2 water by-pass hose from the throttle body.

  1. Disconnect the No. 1 throttle body hose from the throttle body.

  1. Disconnect the throttle position sensor and control motor connector.

  1. Disconnect the wire harness clamp.

  1. Disconnect the fuel tube from the clamp.

  1. A124565
    Remove the 4 bolts, and then remove the fuel pipe support and throttle body.

  1. A124566
    Remove the gasket from the intake manifold.


12. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. A125333
    Remove the 2 wire harness clamps.

  1. Disconnect the 4 fuel injector connectors.

  1. A125334
    Remove the 2 bolts and then pull out the fuel delivery pipe together with the 4 fuel injectors.

    NOTICE:
    Be careful not to drop the fuel injectors when removing the fuel delivery pipe.

  1. A125335
    Remove the 2 delivery pipe spacers from the cylinder head.

  1. Remove the 4 insulators from the cylinder head.


13. REMOVE INTAKE MANIFOLD
  1. Disconnect the union to check valve hose from the brake booster.

  1. A125028
    Disconnect the camshaft timing oil control valve connector.

  1. Remove the wire harness clamp.

  1. Remove the union to check valve hose from the vacuum hose clamp.

  1. Remove the 5 bolts, 2 nuts and intake manifold.

  1. A090130E01
    Remove the gasket from the intake manifold.


14. REMOVE INTAKE MANIFOLD INSULATOR

  1. A095425E01
    Remove the intake manifold insulator from the cylinder block.


15. REMOVE FRONT EXHAUST PIPE
  1. Remove the 2 bolts, 2 compression springs and front exhaust pipe.

  1. Remove the gasket from the exhaust manifold.

    A126831


16. REMOVE OIL DIPSTICK

17. REMOVE OIL DIPSTICK GUIDE

  1. A112218
    Remove the bolt and guide.

  1. Remove the O-ring from the guide.


18. REMOVE MANIFOLD STAY

  1. A112193
    Remove the bolt, nut and stay.


19. REMOVE NO. 2 MANIFOLD STAY

  1. A112192
    Remove the bolt, nut and stay.


20. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

  1. A112189
    Remove the 4 bolts and heat insulator.


21. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

  1. A098744E01
    Disconnect the air-fuel ratio sensor connector.

  1. A112190
    Remove the 5 nuts, manifold converter and gasket.


22. DISCONNECT NO. 1 RADIATOR HOSE

  1. A114348
    Disconnect the hose from the cylinder head.


23. DISCONNECT ENGINE WIRE

  1. A098748E01
    Disconnect the radio setting condenser connector.

  1. Disconnect the engine oil pressure switch connector.

  1. Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the camshaft position sensor connector.

  1. Remove the bolt and ground cable.


24. REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH
  1. Remove the 4 bolts and reinforcement RH.


25. REMOVE FAN AND GENERATOR V BELT

  1. A114351E01
    Using SST and 19 mm socket wrench, loosen the V-ribbed belt tensioner arm clockwise, then remove the fan and generator V belt.
    SST
    09216-42010  

    NOTICE:
    1. Be sure to connect SST and the tools so that they are in line during use.
    2. When retracting the tensioner, turn it clockwise slowly for 3 seconds or more. Do not apply force rapidly.
    3. After the tensioner is fully retracted, do not apply force any more than necessary.


26. REMOVE IDLER PULLEY

  1. A132481
    Loosen the 2 bolts and remove the idler bracket with the 2 bolts.


27. REMOVE GENERATOR ASSEMBLY

A122809
  1. Disconnect the generator connector.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the generator wire.

  1. Remove the bolt and wire harness clamp bracket.

  1. Remove the wire harness clamps.

  1. A122810
    Remove the 2 bolts and generator.


28. REMOVE ENGINE MOUNTING INSULATOR RH

  1. A098189E02
    Remove the bolt of the wire harness protector.

  1. Disconnect the 2 clamps of the engine wire.

  1. A061184E04
    Place a transmission jack underneath the engine, then put a wooden block on the jack.

  1. A124843
    Remove the 4 bolts, 2 nuts and engine mounting insulator RH.

    NOTICE:
    Do not apply excessive force to the return tube when removing the engine mounting insulator RH.

    HINT:
    Keep clearance by lowering the engine using the transmission jack when removing the engine mounting insulator FR.


29. REMOVE IGNITION COIL ASSEMBLY
  1. Disconnect the 4 ignition coil connectors.

  1. A124400
    Remove the 4 bolts and 4 ignition coils.


30. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

  1. A112209
    Disconnect the 2 ventilation hoses from the cylinder head cover.

  1. A112210E01
    Remove the 2 bolts and disconnect the 2 engine wires.

  1. A112211
    Remove the 8 bolts, 2 nuts and cylinder head cover.


31. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
  1. Lift the engine upward using the transmission jack.

    NOTICE:
    Do not lift the engine more than necessary.

  1. A112212
    Remove the bolt, nut and V-ribbed belt tensioner.


32. REMOVE CRANKSHAFT POSITION SENSOR

A097797E01
  1. Disconnect the sensor connector.

  1. Remove the connector clamp.

  1. Remove the wire harness from the wire harness clamp bracket.

  1. Remove the wire harness clamp.

  1. Remove the bolt and sensor.


33. REMOVE OIL PAN SUB-ASSEMBLY

  1. A112213E01
    Install the No. 1 and No. 2 engine hangers with the bolts.

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

    Part No. 
    Item
    Part No.
    No. 1 engine hanger
    12281-28010
    No. 2 engine hanger
    12282-28010
    Bolt
    91512-61020

  1. Attach the sling device to the engine hangers and chain block.

  1. A114333
    Remove the 12 bolts and 2 nuts.

  1. A000019E05
    Insert the blade of SST between the crankcase, chain cover and oil pan, then cut off the applied sealer and remove the oil pan.
    SST
    09032-00100  

    NOTICE:
    Be careful not to damage the contact surface of the crankcase, chain cover and oil pan.


34. SET NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A098345E09
    Turn the crankshaft pulley until its groove and the timing mark "0" of the timing chain cover are aligned.

  1. Check that each timing mark of the camshaft timing gear and sprocket is aligned with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.
    If not, turn the crankshaft by 1 revolution (360°) to align the timing marks as above.


35. REMOVE NO. 2 CAMSHAFT

  1. A098172E05
    Place paint marks on the chain in alignment with the timing marks on the camshaft timing gear and camshaft timing sprocket.

  1. A098348E03
    Remove the 2 nuts, tensioner and gasket.

  1. A098173E03
    While holding the camshaft with a wrench, loosen the camshaft timing set bolt.

  1. A098174E08
    Using several steps, uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 5 bearing caps.

  1. A052473E02
    While holding the No. 2 camshaft by hand, remove the camshaft timing sprocket set bolt.

  1. Remove the camshaft timing sprocket from the No. 2 camshaft with the timing chain wrapped on the sprocket.

  1. Remove the camshaft timing sprocket from the timing chain.


36. REMOVE CAMSHAFT

  1. A098175E02
    Using several steps, uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 5 bearing caps.

  1. Remove the camshaft and camshaft timing gear while holding the timing chain by hand.

  1. A056228E01
    Tie the timing chain with a string as shown in the illustration.

    NOTICE:
    Be careful not to drop anything inside the timing chain cover.


37. REMOVE CRANKSHAFT PULLEY

  1. A013697E02
    Using SST, fix the pulley in place and loosen the pulley bolt.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A124860E01
    Remove the crankshaft pulley.

    HINT:
    If necessary, remove the pulley with SST and the pulley bolt.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)
    09950-40011   (09957-04010)


38. REMOVE ENGINE MOUNTING BRACKET RH

  1. A128165
    Remove the 3 bolts and engine mounting bracket RH.


39. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A014253E03
    Using an E10 "torx" socket, remove the stud bolt for the V-ribbed belt tensioner.

  1. A132568E01
    Remove the 12 bolts and 2 nuts.

  1. A128179
    Remove the timing chain cover by prying the portions between the timing chain cover, cylinder head and cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder head and cylinder block.


40. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

41. REMOVE TIMING CHAIN GUIDE

  1. A077243E01
    Remove the bolt and timing chain guide.


42. REMOVE CHAIN TENSIONER SLIPPER

  1. A128183
    Remove the bolt and chain tensioner slipper.


43. REMOVE CHAIN SUB-ASSEMBLY

44. REMOVE NO. 1 CHAIN VIBRATION DAMPER

  1. A128184
    Remove the 2 bolts and chain vibration damper.


45. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A124556
    Disconnect the oil control valve connector.

  1. Remove the bolt and oil control valve.


46. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

  1. A090848E03
    Clamp the camshaft in a vise, and make sure that the camshaft timing gear does not rotate.

  1. Cover all the oil ports with vinyl tape except the advance side port shown in the illustration.

  1. A031032E02
    Apply air pressure of 100 kPa (1.0 kgf/cm2, 14 psi) to the oil path, then turn the camshaft timing gear to the advance direction (counterclockwise) by hand.

    CAUTION:
    Cover the paths with a shop rag to avoid oil splashes.

    HINT:
    Depending on the air pressure, the camshaft timing gear will turn to the advance angle side without applying force by hand. Also, under the condition that the pressure is difficult to apply because of air leakage from the port, there may be the case that the lock pin is difficult to release.

  1. A032639E02
    Remove the flange bolt of the camshaft timing gear.

    NOTICE:
    1. Be sure not to remove the other 4 bolts.
    1. When reusing the camshaft timing gear, release the straight lock pin first, then install the gear.


47. REMOVE CYLINDER HEAD SUB-ASSEMBLY

  1. F050595E01
    Using several steps, uniformly loosen and remove the 10 cylinder head bolts and 10 plate washers with a 10 mm bi-hexagon wrench in the sequence shown in the illustration.

    NOTICE:
    Head warpage or cracking could result from removing the bolts in the wrong order.

  1. A126930
    Using a screwdriver, pry between the cylinder head and cylinder block, and remove the cylinder head.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and cylinder block.


48. REMOVE CYLINDER HEAD GASKET

A126929
← COMPONENTS (from Nov 2005)REMOVAL (Jan 2007 – Jul 2007) →