2005-2008 RAV4 · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built Nov 2005 – Dec 2006

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008 from Aug 2008


1. INSTALL LOWER INSTRUMENT PANEL
  1. Connect the connectors and clamps and install the lower instrument panel.

  1. Install the 2 bolts, 3 screws and 2 clips.

    B129871


2. INSTALL NO. 6 HEATER TO REGISTER DUCT ASSEMBLY (w/ Cool Box)

B139535
  1. Install the duct with the 2 screws.


3. INSTALL POWER STEERING ECU ASSEMBLY

C128905E01
  1. Install the ECU with the 3 nuts.

  1. Connect the connectors.


4. INSTALL INSTRUMENT PANEL BOX

B129874
  1. Attach the 6 clips to install the instrument panel box.

  1. Install the screw.


5. INSTALL INSTRUMENT PANEL SAFETY PAD COVER (for LHD)

B132920
  1. Attach the 4 claws to install the instrument panel safety pad cover.


6. INSTALL NO. 1 SWITCH HOLE BASE

B129875
  1. Connect the connectors.

  1. Attach the 4 clips to install the switch hole base.


7. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

B129887
  1. Attach the 2 hinges to install the door.

  1. B129889E03
    Attach the claw to the glove compartment door stopper.

  1. While pushing in the sides of the glove compartment door as indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.


8. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Knee Airbag)

B129997
  1. Attach the 2 claws to install the instrument panel under cover.


9. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL (w/o Knee Airbag)

B132919
  1. Attach the 8 claws to install the lower instrument panel finish panel.

  1. Install the 2 screws.


10. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Knee Airbag)

B127987
  1. Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Install the driver side knee airbag with the 4 bolts.

    Torque:
    10 N*m{ 101 kgf*cm , 7 ft.*lbf }


11. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Knee Airbag)

B129996
  1. Attach the 2 claws to install the instrument panel under cover.

  1. Install the 2 screws.


12. INSTALL REAR CONSOLE BOX SUB-ASSEMBLY

B129878
  1. Connect the connector.

  1. Install the rear console box with the 2 bolts and 2 screws.

  1. Install the console box carpet.


13. INSTALL NO. 1 INSTRUMENT PANEL BRACKET COVER INNER LH

B129877
  1. Attach the 2 claws to install the instrument panel bracket cover.


14. INSTALL NO. 1 INSTRUMENT PANEL BRACKET COVER INNER RH

B129876
  1. Attach the 2 claws to install the instrument panel bracket cover.


15. INSTALL CONSOLE REAR END PANEL

B129879
  1. Attach the 6 claws to install the console rear end panel.


16. INSTALL UPPER REAR CONSOLE PANEL SUB-ASSEMBLY

B129880
  1. Connect the connector.

  1. Attach the 4 clips to install the upper rear console panel.


17. INSTALL CONSOLE CUP HOLDER BOX

B129881
  1. Attach the 2 clips to install the cup holder box.

  1. Install the 2 screws.


18. INSTALL SWITCH BASE

B129882
  1. Connect the connectors.

  1. Attach the 2 clips and 2 claws to install the switch base.


19. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

B129883
  1. Automatic transaxle:
    Connect the connector.

  1. Attach the 2 clips and 4 claws to install the upper console panel.

  1. Install the shift lever knob.


20. INSTALL NO. 2 CONSOLE UPPER PANEL GARNISH

B129884
  1. Attach the 4 clips to install the upper panel garnish.


21. INSTALL NO. 1 CONSOLE UPPER PANEL GARNISH

B129885
  1. Attach the 4 clips to install the upper panel garnish.


22. INSTALL HEATER CONTROL SUB-ASSEMBLY (for Automatic Air Conditioning System)

  1. E118690
    Connect the connectors.

  1. Attach the 3 clips to install the air conditioning control.

  1. Install the 2 screws.


23. INSTALL HEATER CONTROL SUB-ASSEMBLY (for Manual Air Conditioning System)

  1. E118688
    Connect the connectors.

  1. Attach the 3 clips to install the air conditioning control.

  1. Install the 2 screws.


24. INSTALL WINDSHIELD WIPER SWITCH ASSEMBLY

25. INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY

26. INSTALL SPIRAL CABLE SUB-ASSEMBLY
  1. Check that the front wheels are facing straight ahead.

  1. Set the turn signal switch to the neutral position.

    NOTICE:
    Make sure that the turn signal switch is in the neutral position, as the pin of the turn signal switch may be snapped.

  1. B127903E01
    B127902E01
    Install the spiral cable.

    NOTICE:
    When replacing the spiral cable with a new one, remove the lock pin before installing the steering wheel.

  1. Connect the connectors to the spiral cable.

    NOTICE:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. B127901E01
    Attach the 4 clips to the column cover (upper).

  1. B127900E02
    Install the steering column cover (upper).


27. INSTALL STEERING COLUMN COVER
for LHD (Click here)
for RHD (Click here)

28. INSTALL STEERING WHEEL ASSEMBLY
for LHD (Click here)
for RHD (Click here)

29. INSTALL STEERING PAD ASSEMBLY

B127893E01
  1. Support the steering pad with one hand as shown in the illustration.

  1. Connect the 2 airbag connectors.

    NOTICE:
    When handling the airbag connector, do not damage the airbag wire harness.

  1. Connect the horn connector.

  1. Install the steering pad after confirming that the circumference grooves of the screws are caught on the screw case.

  1. B130245E02
    Using a T30 "torx" driver, install the 2 screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }


30. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY
  1. Install the instrument panel (Click here).


31. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

32. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).

← REASSEMBLY (from Aug 2008)INSTALLATION (Jan 2007 – Jul 2007) →