2005-2008 RAV4 · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. DISCHARGE FUEL SYSTEM PRESSURE procedures must be performed before disconnecting any part of the fuel system.
  2. After performing the DISCHARGE FUEL SYSTEM PRESSURE procedures, pressure will remain in the fuel line. When disconnecting the fuel line, place a cloth or equivalent over fittings to reduce the risk of fuel spray.

  1. Remove the console box (Click here).

  1. A128750E01
    Disconnect the connector.

  1. Start the engine. After the engine has stopped, turn the ignition switch off.

    HINT:
    DTC P0171 (system too lean) may be set.

  1. Check that the engine does not start.

  1. Remove the fuel tank cap, and let the air out of the fuel tank.

  1. A128750E01
    Connect the connector.

  1. Install the console box (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


3. REMOVE HOOD SUB-ASSEMBLY
  1. Remove the engine hood (Click here).


4. REMOVE RADIATOR SUPPORT OPENING COVER

5. REMOVE BATTERY CLAMP SUB-ASSEMBLY
  1. Loosen the bolt and nut, and remove the battery clamp.


6. REMOVE BATTERY

7. REMOVE BATTERY TRAY

8. REMOVE FRONT WHEEL

9. REMOVE NO. 1 ENGINE UNDER COVER

10. REMOVE NO. 2 ENGINE UNDER COVER

11. REMOVE FRONT FENDER APRON RH

12. REMOVE NO. 1 ENGINE COVER

  1. A112206
    Remove the 2 nuts and cover.


13. DRAIN ENGINE COOLANT
  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Remove the radiator reservoir cap.

    CAUTION:
    Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the cylinder block drain cock plug.

    A112179E01


14. DRAIN AUTOMATIC TRANSAXLE FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    47 N*m{ 479 kgf*cm , 35 ft.*lbf }


15. DRAIN MANUAL TRANSAXLE OIL
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


16. REMOVE RADIATOR ASSEMBLY
  1. Remove the radiator (Click here).


17. REMOVE RADIATOR RESERVOIR TANK

  1. A124838
    Remove the 2 bolts and radiator reservoir.


18. REMOVE PURGE VSV

  1. A124790
    Disconnect the purge VSV connector.

  1. Disconnect the wire harness clamp.

  1. Disconnect the 2 purge line hoses from the purge VSV.

  1. Remove the purge VSV from the air cleaner hose.


19. REMOVE AIR CLEANER CAP

  1. A124559
    Disconnect the mass air flow meter connector.

  1. Disconnect the purge VSV connector.

  1. Disconnect the 4 wire harness clamps.

  1. A124560
    Disconnect the No. 2 ventilation hose from the air cleaner hose.

  1. Disconnect the purge line hose from the clamp.

  1. A124561
    Squeeze the tabs of the No. 1 air cleaner hose clamp, and then disconnect the No. 1 air cleaner hose from the throttle body.

  1. A124562
    Unfasten the 2 hook clamps, and then remove the air cleaner cap.

  1. Remove the air cleaner filter element from the air cleaner case.


20. REMOVE AIR CLEANER CASE

  1. A112221
    Remove the 3 bolts from the air cleaner case.

  1. Disconnect the case from the No. 1 air cleaner inlet.


21. REMOVE FRONT BATTERY CARRIER

  1. A124827
    Disconnect the 2 clamps of the engine wire.

  1. Remove the 4 bolts and front battery carrier.


22. REMOVE BATTERY BRACKET REINFORCEMENT

  1. A124828
    Remove the 2 bolts and battery bracket reinforcement.


23. REMOVE BATTERY CARRIER BRACKET

  1. A124829
    Remove the 2 bolts, nut and battery carrier bracket.


24. DISCONNECT UNION TO CONNECTOR TUBE HOSE (for LHD)

  1. A124830
    Disconnect the 2 union to connector tube hoses from the booster vacuum tube.


25. DISCONNECT UNION TO CONNECTOR TUBE HOSE (for RHD)

  1. A126899
    Disconnect the union to connector tube hose from the booster vacuum tube.


26. DISCONNECT HEATER WATER INLET HOSE

  1. A124832
    Disconnect the heater water inlet hose from the heater unit.


27. DISCONNECT HEATER WATER OUTLET HOSE

  1. A124831
    Disconnect the heater water outlet hose from the heater unit.


28. DISCONNECT FUEL TUBE

A125337E01

NOTICE:
Do not forcibly bend and twist the fuel main tube.

  1. Remove the fuel tube from the fuel hose clamp.

  1. Remove the fuel pipe clamp.

  1. Wipe off any dirt on the fuel tube connector.

  1. Hold the fuel tube connector, and then install the SST.

    SST
    09268-21010  

  1. Turn the SST to align the retainer inside the fuel tube connector with the chamfered part of the SST.

  1. Insert the SST into the fuel tube and hold it. Then push the fuel tube connector toward the SST side.

  1. Mount the retainer of the fuel tube connector onto the chamfered part of the SST.

  1. A076220E05
    Slide the SST and fuel tube connector together towards the fuel tube until they make a "click" sound, and then disconnect the fuel tube.

  1. Drain the fuel remaining inside the fuel tube.

  1. Cover the fuel tube and fuel pipe with a plastic bag to protect the disconnected part.


29. DISCONNECT NO. 2 VENTILATION HOSE

  1. A097786E01
    Disconnect the No. 2 ventilation hose from the ventilation valve.


30. REMOVE THROTTLE BODY

  1. A124564
    Disconnect the purge line hose from the throttle body.

  1. Disconnect the water by-pass hose from the throttle body.

  1. Disconnect the No. 2 water by-pass hose from the throttle body.

  1. Disconnect the No. 1 throttle body hose from the throttle body.

  1. Disconnect the throttle position sensor and control motor connector.

  1. Disconnect the wire harness clamp.

  1. Disconnect the fuel tube from the clamp.

  1. A124565
    Remove the 4 bolts, and then remove the fuel pipe support and throttle body.

  1. A097781E01
    Remove the gasket from the intake manifold.


31. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

  1. A125333
    Remove the 2 wire harness clamps.

  1. Disconnect the 4 fuel injector connectors.

  1. A125334
    Remove the 2 bolts and then pull out the fuel delivery pipe together with the 4 fuel injectors.

    NOTICE:
    Be careful not to drop the fuel injectors when removing the fuel delivery pipe.

  1. A125335
    Remove the 2 delivery pipe spacers from the cylinder head.

  1. Remove the 4 insulators from the cylinder head.


32. REMOVE INTAKE MANIFOLD
  1. Disconnect the union to check valve hose from the brake booster.

  1. A097788E01
    Disconnect the camshaft timing oil control valve connector.

  1. Remove the wire harness clamp.

  1. Remove the union to check valve hose from the vacuum hose clamp.

  1. Remove the 5 bolts, 2 nuts and intake manifold.

  1. A090130E01
    Remove the gasket from the intake manifold.


33. REMOVE INTAKE MANIFOLD INSULATOR

  1. A095425E01
    Remove the intake manifold insulator from the cylinder block.


34. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transaxle)

C130918
  1. Remove the nut and disconnect the control cable from the control shaft lever.

  1. C127839
    Remove the clip and disconnect the control cable from the control cable bracket.

  1. C127838
    Disconnect the control cable from the control cable support.

  1. C127836
    Remove the bolt and disconnect the clamp of the control cable.

  1. C130920
    Disconnect the control cable from the shift lever.

  1. C127813E01
    Turn the nut and disconnect the control cable from the shift lever retainer.

  1. C127837
    Remove the 2 bolts and control cable.


35. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)

G024413E01
  1. Removal the 2 clips and washers, and disconnect the top ends of the control cable from the transaxle.

  1. Remove the 2 clips and disconnect the control cable bracket.

  1. C127242
    Remove the 2 bolts from the retainer.

  1. Pull out the control cable from the floor.


36. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transaxle)

C127496
  1. Remove the 4 bolts and clutch release cylinder.


37. REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH
  1. Remove the 4 bolts and reinforcement RH.


38. REMOVE FAN AND GENERATOR V BELT

  1. A114351E01
    Using SST 19 mm socket wrench, loosen the V-ribbed belt tensioner arm clockwise, then remove the fan and generator V belt.
    SST
    09216-42010  

    NOTICE:
    1. Be sure to connect SST and the tools so that they are in line during use.
    2. When retracting the tensioner, turn it clockwise slowly for 3 seconds or more. Do not apply force rapidly.
    3. After the tensioner is fully retracted, do not apply force any more than necessary.


39. REMOVE GENERATOR ASSEMBLY

  1. A122815
    Disconnect the generator connector.

  1. Remove the terminal cap.

  1. Remove the nut and disconnect the generator wire.

  1. Remove the bolt and wire harness clamp bracket.

  1. Remove the wire harness clamp.

  1. A122816
    Remove the 2 bolts and generator.


40. REMOVE COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

HINT:
Disconnect the compressor together with the low-pressure and high-pressure hoses, then secure it to the vehicle side using rope.


41. REMOVE ECM
  1. Remove the ECM (Click here).


42. DISCONNECT ENGINE WIRE
  1. Remove the engine room relay block cover.

  1. A124834
    Remove the nut and disconnect the 2 engine wire connectors.

  1. A124847
    Remove the bolt and engine wire cover.
    Then disconnect the engine wire from the engine wire cover clamp.

  1. A124835
    Disconnect the ground cable connector.

  1. A124836
    Remove the nut from the positive (+) battery terminal to disconnect the engine wire.

  1. A124837
    Disconnect the ground cable from the clamp located near the starter.

  1. Remove the bolt and ground cable located near the starter.


43. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Remove the 2 bolts, 2 compression springs and front exhaust pipe.

  1. Remove the gasket from the exhaust manifold.

    A126831


44. REMOVE FRONT DRIVE SHAFT ASSEMBLY
  1. Remove the front drive shaft (Click here).


45. REMOVE PROPELLER SHAFT WITH CENTER BEARING SHAFT ASSEMBLY

  1. C127524
    Remove the 2 bolts and 2 adjusting washers, and disconnect the propeller with center bearing shaft.

    NOTICE:
    1. During the removal, do not exert excessive force on the universal joint.
    2. When removing, transporting or storing the propeller with center bearing shaft assembly, do not allow the No. 2 joint angle to exceed 20°.

  1. C127525E01
    Place matchmarks on the differential carrier and propeller shaft.

  1. Remove the 4 nuts and 4 washers, and disconnect the propeller shaft and differential carrier.

  1. C127526E01
    Place matchmarks on the transfer and propeller shaft.

  1. Remove the 4 nuts and 4 washers, and disconnect the propeller shaft from the transfer.


46. REMOVE ENGINE MOUNTING INSULATOR FR

  1. A124839
    Remove the through bolt and nut.

  1. A124840
    Remove the 2 bolts and engine mounting insulator FR.


47. REMOVE ENGINE MOUNTING INSULATOR RR

  1. A124841
    Remove the through bolt.

  1. A124842
    Remove the 2 nuts, 2 bolts and engine mounting insulator RR.


48. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

  1. A112213E01
    Install the No. 1 and No. 2 engine hangers with the bolts as shown in the illustration.

    Part No.:
    Item
    Part No.
    No. 1 engine hanger
    12281-28010
    No. 2 engine hanger
    12282-28010
    Bolt
    91512-61020

    Torque:
    38 N*m{ 387 kgf*cm , 28 ft.*lbf }

  1. A114336
    Attach the sling device to the engine hangers and chain block.

  1. Carefully remove the engine with transaxle from the vehicle.


49. REMOVE ENGINE MOUNTING INSULATOR RH

  1. A124843
    Remove the 2 nuts, 4 bolts and engine mounting insulator RH.


50. REMOVE ENGINE MOUNTING INSULATOR LH

  1. A124844
    Remove the through bolt and nut.

  1. A124845
    Remove the 4 bolts and engine mounting insulator LH.


51. REMOVE DRIVE SHAFT BEARING BRACKET

  1. A098759E01
    Remove the 3 bolts and bracket.


52. REMOVE TRANSFER ASSEMBLY

C126622
  1. Remove the 6 nuts, 2 bolts and transfer from the transaxle.


53. REMOVE STARTER ASSEMBLY

  1. A124920
    Disconnect the starter connector.

  1. Open the terminal cap, remove the nut and disconnect the starter wire.

  1. A124921
    Remove the 2 bolts and starter.


54. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

C127819
  1. Remove the flywheel housing under cover.

  1. Turn the crankshaft to gain access and remove the 6 bolts while holding the crankshaft pulley bolt with a wrench.

  1. C127820
    Remove the 4 lower side mounting bolts.

  1. C127822
    Remove the 5 upper side mounting bolts.

  1. Separate and remove the automatic transaxle.


55. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY (for Automatic Transaxle)

56. REMOVE DRIVE PLATE SUB-ASSEMBLY (for Automatic Transaxle)

  1. A126932E01
    Using SST, hold the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A112224
    Remove the 8 bolts, rear spacer, drive plate and front spacer.


57. REMOVE FLYWHEEL HOUSING UNDER COVER (for Manual Transaxle)

C127239
  1. Remove the 2 bolts and insulator from the stiffener plate.


58. REMOVE STIFFENER PLATE LH (for Manual Transaxle)

C127240
  1. Remove the 4 bolts and stiffener plate from the engine and transaxle assembly.


59. REMOVE STIFFENER PLATE RH (for Manual Transaxle)

C127241
  1. Remove the 4 bolts and stiffener plate from the engine and transaxle assembly.


60. REMOVE MANUAL TRANSAXLE ASSEMBLY

D025747E01
  1. Remove the 10 bolts.

  1. Separate and remove the transaxle from the engine.


61. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle)

C127502E01
  1. Place matchmarks on the cover and flywheel.

  1. Loosen each set bolt one turn at a time until the spring tension is released.

  1. Remove the 6 set bolts and pull off the cover.

    NOTICE:
    Do not drop the clutch disc.


62. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)

63. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

  1. A126932E01
    Using SST, hold the crankshaft.
    SST
    09213-54015   (91651-60855)
    09330-00021  

  1. A112225
    Remove the 8 bolts and flywheel.

← REMOVAL (Jan 2007 – Jul 2007)INSTALLATION (Nov 2005 – Dec 2006) →