Illumination Circuit
Circuit diagnosis · Vehicles built from Nov 2005
DESCRIPTION
The main body ECU receives information regarding the door courtesy switch and door lock position switch, and turns on the room light assembly.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MAIN BODY ECU) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and press the intelligent tester main switch ON.
Select the item below in the ACTIVE TEST and then check that the relay operates.
Main body ECU Item
Test Details
Diagnostic Note
Illumi Output
Test Details:
Turn interior light and key illumination ON/OFF
Vehicle Condition:
Room light SW is in DOOR position and all doors are closed
-
- OK:
- Headlights (LOW) come on.
|
|
||||
| NG | |
| 2. INSPECT FUSE (DOME) |
Remove the DOME fuse from the engine room No. 2 relay block.
Measure the resistance of the fuse.
- Standard resistance:
- Below 1 Ω
|
|
||||
| OK | |
| 3. INSPECT ROOM LIGHT ASSEMBLY |
![]() ![]() |
Remove the room light assembly.
Measure the resistance of the room light switch base.
- Standard resistance:
Tester Connection
Switch Operation
Specified Condition
1 - 2
1 - 3
OFF
10 kΩ or higher
1 - 2
DOOR
Below 1 Ω
1 - 3
ON
Below 1 Ω
|
|
||||
| OK | |
| 4. INSPECT ROOM LIGHT BULB |
![]() ![]() |
Remove the room light assembly.
Connect the positive (+) lead from the battery to terminal 1 and the negative (-) lead to terminal 2, then check that the bulb illuminates when the switch is in the DOOR position.
- OK:
- Bulb illuminates.
Connect the positive (+) lead from the battery to terminal 1 and the negative (-) lead to terminal 3, then check that the bulb illuminates when the switch is in the ON position.
- OK:
- Bulb illuminates.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (BATTERY - ROOM LIGHT AND JUNCTION BLOCK) |
![]() ![]() |
Disconnect the IK instrument panel junction block connector.
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Condition
Specified Condition
IK-2 - Body ground
Room light switch in DOOR position
10 to 14 V
|
|
||||
| OK | |
| 6. INSPECT MAP LIGHT BULB |
![]() ![]() ![]() ![]() |
Remove the map light assembly.
Connect the positive (+) lead from the battery to terminal 6 and the negative (-) lead to terminal 1, then check that the bulb illuminates when the switch is in the DOOR position.
- OK:
- Bulb illuminates.
Connect the positive (+) lead from the battery to terminal 6 and the negative (-) lead to terminal 7, then check that the bulb illuminates when the switch is in the ON position.
- OK:
- Bulb illuminates.
|
|
||||
| NG | |
| 7. INSPECT MAP LIGHT |
Remove the map light assembly.
Replace the map light bulb.
Inspect the map light.

Connect the positive (+) lead from the battery to terminal 6 and the negative (-) lead to terminal 1, then check that the light comes on when the switch is in the DOOR position.
- OK:
- Light comes on.
Connect the positive (+) lead from the battery to terminal 6 and the negative (-) lead to terminal 7, then check that the light comes on when the switch is in the ON position.

- OK:
- Light comes on.
|
|
||||
| OK | |
| 8. CHECK WIRE HARNESS (BATTERY - MAP LIGHT AND JUNCTION BLOCK) |
![]() ![]() |
Disconnect the IK instrument panel junction block connector.
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Condition
Specified Condition
IK-2 - Body ground
Room light switch in DOOR position
10 to 14 V
|
|
||||
| OK | |
| 9. INSPECT IGNITION KEY CYLINDER LIGHT |
RHD and w/o Entry and start system, w/ Engine immobiliser system

Remove the transponder key amplifier.
Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 6, then check that the light comes on.
- OK:
- Light comes on.
w/ Entry and start system and w/o Engine immobiliser system

Remove the ignition key cylinder light.
Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the light comes on.
- OK:
- Light comes on.
|
|
||||
| OK | |
| 10. CHECK WIRE HARNESS (INSTRUMENT PANEL JUNCTION BLOCK - BATTERY) |
![]() ![]() |
Disconnect the IE instrument panel junction block connector.
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
IE-27 (ILE) - Body ground
10 to 14 V
|
|
||||
| OK | ||
| ||




