When replacing the disc with a new one, select the installation position where the disc has the smallest runout.
2.
INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG
Install the adjusting hole plug to the rear disc.
3.
CHECK DISC RUNOUT
Check the bearing backlash and axle hub deviation (Click here).
Tighten the disc with the 5 hub nuts.
Torque:
103 N*m{
1050 kgf*cm
, 76 ft.*lbf
}
Using a dial indicator, measure the disc runout 10 mm (0.39 in.) from the outer edge of the disc.
Maximum disc runout:
0.15 mm (0.0059 in.)
If the runout is more than the maximum, change the installation positions of the disc and axle so that the runout is the smallest possible. If the runout is more than the maximum even when the installation positions are changed, grind the disc. If the disc thickness is less than the minimum, replace the disc.
Remove the 5 hub nuts and disc.
4.
ADJUST PARKING BRAKE SHOE CLEARANCE
Temporarily install the hub nuts.
Remove the shoe adjusting hole plug, and then turn the adjuster to expand the shoe adjuster until the disc locks.
Turn the shoe adjuster so that it contracts to a point where the disc can rotate smoothly.
Temporarily install the bleeder plug to the brake cylinder.
HINT:
The bleeder plug will be tightened to a torque specification in the "BLEED AIR FROM BRAKE LINE" procedures.
Install the bleeder plug cap to the bleeder plug.
6.
INSTALL PISTON SEAL
Apply a light coat of lithium soap base glycol grease to the entire inner and outer circumference of a new piston seal.
Install the piston seal to the brake cylinder.
NOTICE:
Securely install the piston seal into the groove of the disc brake cylinder.
7.
INSTALL REAR DISC BRAKE PISTON
Apply a light coat of lithium soap base glycol grease to the entire inner and outer circumference of a new cylinder boot.
Apply a light coat of lithium soap base glycol grease to the entire outer circumference of the rear disc brake piston where it contacts the rear disc brake cylinder.
Install the cylinder boot to the rear disc brake piston.
Install the rear disc brake piston to the rear disc brake cylinder assembly.
NOTICE:
Do not forcibly install the brake piston to the brake cylinder.
8.
INSTALL CYLINDER BOOT
Install the cylinder boot to the cylinder.
NOTICE:
Install the boot securely into the grooves of the brake cylinder and brake piston.
Be careful not to damage the boot.
Using a screwdriver, install a new set ring.
NOTICE:
Be careful not to damage the boot.
HINT:
Tap the screwdriver tip before use.
9.
INSTALL REAR DISC BRAKE BUSH DUST BOOT
Apply a light coat of lithium soap base glycol grease to the entire circumference of a new rear disc brake bush dust boot where it contacts the rear disc brake cylinder mounting, and the entire inner circumference of its both ends.
NOTICE:
Apply a sufficient amount of lithium soap base glycol grease to the entire circumference of the rear disc brake bush dust boot and rear disc brake cylinder mounting contact surfaces.
HINT:
Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to the rear disc brake bush dust boot.
Install the 2 boots to the mounting.
10.
INSTALL REAR DISC BRAKE CYLINDER SLIDE BUSH
Apply a light coat of lithium soap base glycol grease to the rear disc brake cylinder slide pin where it contacts rear disc brake cylinder slide bush.
Install the slide bush to the slide pin.
11.
INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN
Apply lithium soap base glycol grease to the sliding part and the seal surface of the 2 rear disc brake cylinder slide pins.
Install the 2 slide pins (upper and lower) to the mounting.
12.
INSTALL REAR DISC BRAKE CYLINDER MOUNTING LH
Install the cylinder mounting with the 2 bolts.
Torque:
88 N*m{
897 kgf*cm
, 65 ft.*lbf
}
13.
INSTALL REAR DISC BRAKE PAD SUPPORT PLATE
Install the 2 plates to the mounting.
14.
INSTALL PAD WEAR INDICATOR PLATE
Install the 2 indicator plates to the lower side of each pad.
15.
INSTALL ANTI-SQUEAL SHIM
Apply disc brake grease to both sides of each No. 1 shim.
Install the No. 1 and No. 2 shims to the pads.
NOTICE:
When replacing a worn pad, the shims must be replaced together with the pads.
Install the shims in the correct positions and direction as shown in the illustration.
16.
INSTALL REAR DISC BRAKE PAD
Install the 2 disc brake pads to the mounting.
NOTICE:
Make sure there is no oil or grease on the friction surface of the pads and disc.