REMOVAL
Removal / installation · Vehicles built Nov 2005 – Jul 2008
Versions by build date: Nov 2005 – Jul 2008 from Aug 2008
| 1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
 |
- CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
| 2.
REMOVE REAR BUMPER COVER |
 |
- Remove the 9 screws and 7 clips.
w/ Rear Quarter Panel Mudguard:
Remove the rear quarter panel mudguard.
Put protective tape under the quarter panel.
- Detach the 12 claws and remove the bumper cover.
w/ Fog Light:
Disconnect the 2 fog light connectors.
w/ License Light:
Disconnect the license plate light connector.
Remove the 2 license plate lights (Click here).
| 3.
REMOVE REAR BUMPER PROTECTOR |
 |
- HINT:
- When removing the bumper protector, heat the bumper protector.
- Standard heating temperature:
Item
|
Specified Condition
|
Bumper protector
|
40 to 60°C (104 to 140°F)
|
- Using a moulding remover, remove the bumper protector.
| 4.
REMOVE REAR FOG LIGHT ASSEMBLY LH (w/ Rear Fog Light) |
 |
- Remove the 3 bolts and rear fog light.
| 5.
REMOVE REAR FOG LIGHT ASSEMBLY RH (w/ Rear Fog Light) |
 |
- HINT:
- Use the same procedures described for the LH side.
| 6.
REMOVE REFLEX REFLECTOR ASSEMBLY LH (w/ Reflex Reflector) |
 |
- Remove the screw and reflex reflector.
| 7.
REMOVE REFLEX REFLECTOR ASSEMBLY RH (w/ Reflex Reflector) |
 |
- HINT:
- Use the same procedures described for the LH side.
| 8.
REMOVE REAR BUMPER ABSORBER (for Short Body) |
 |
- Remove the absorber.
| 9.
REMOVE REAR BUMPER REINFORCEMENT (for Short Body) |
 |
- Remove the 6 bolts and reinforcement.
| 10.
REMOVE REAR BUMPER ARM SUPPORT REINFORCEMENT LH (for Short Body) |
 |
- Remove the 3 bolts and bumper arm support.
| 11.
REMOVE REAR BUMPER ARM SUPPORT REINFORCEMENT RH (for Short Body) |
 |
- HINT:
- Use the same procedures described for the LH side.
| 12.
REMOVE REAR BUMPER REINFORCEMENT (for Long Body) |
 |
- Remove the 6 bolts and reinforcement.
| 13.
REMOVE REAR BUMPER SIDE SUPPORT LH (for Short Body) |
 |
- Remove the screw.
Using a screwdriver, detach the claw and remove the bumper side support.
- HINT:
- Tape the screwdriver tip before use.
| 14.
REMOVE REAR BUMPER SIDE SUPPORT RH (for Short Body) |
 |
- HINT:
- Use the same procedures described for the LH side.
| 15.
REMOVE REAR BUMPER SIDE RETAINER LH (for Short Body) |
 |
- Remove the 2 screws.
| 16.
REMOVE REAR BUMPER SIDE RETAINER RH (for Short Body) |
 |
- HINT:
- Use the same procedures described for the LH side.
| 17.
REMOVE REAR BUMPER SIDE SUPPORT LH (for Long Body) |
 |
- Remove the 2 screws.
Using a screwdriver, detach the claw and remove the bumper side support.
- HINT:
- Tape the screwdriver tip before use.
| 18.
REMOVE REAR BUMPER SIDE SUPPORT RH (for Long Body) |
 |
- HINT:
- Use the same procedures described for the LH side.
| 19.
REMOVE REAR BUMPER SIDE RETAINER LH (for Long Body) |
 |
- Remove the screw.
Using a screwdriver, detach the claw and remove the side retainer.
- HINT:
- Tape the screwdriver tip before use.
| 20.
REMOVE REAR BUMPER SIDE RETAINER RH (for Long Body) |
 |
Use the same procedures described for the LH side.
| 21.
REMOVE NO. 1 REAR BUMPER PLATE (for Long Body) |
 |
- Detach the 6 outside moulding retainers and remove the bumper plate.
| 22.
REMOVE REAR BUMPER SIDE MOULDING SUB-ASSEMBLY LH (for Wide Body) |
 |
- Detach the 5 outside moulding retainers and remove the moulding.
- NOTICE:
- If reusing the extension, take care not to damage the moulding.
- Be careful not to damage the vehicle body.
| 23.
REMOVE REAR BUMPER SIDE MOULDING SUB-ASSEMBLY RH (for Wide Body) |
 |
- HINT:
- Use the same procedures described for the LH side.