2005-2008 RAV4 · Service Manual COMMUNICATION SYSTEM

ECM Communication Stop Mode

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

Detection Item
Symptom
Trouble Area
ECM COMMUNICATION STOP MODE
  1. Engine is not displayed on "BUS CHECK" screen of intelligent tester
  2. Applies to "ECM COMMUNICATION STOP MODE" in "DTC COMBINATION TABLE"
  1. Power source or inside ECM
  2. ECM main wire and connector
  3. ECM

WIRING DIAGRAM

C129199E05
C132301E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the main wire and the branch wire.
  2. For Auto:
    After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. For Reminder:
    After the ignition switch is turned off, check that the key reminder warning system and light reminder buzzer are not in operation.
  4. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK WIRE HARNESS (ECM - BATTERY AND BODY GROUND)

  1. Disconnect the A12 and B32 ECM connectors.C129201E03

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for Gasoline Engine:
    Tester Connection
    Specified Condition
    B32-104 (E1) - Body ground
    Below 1 Ω
    B32-45 (E01) - Body ground
    Below 1 Ω
    B32-44 (E02) - Body ground
    Below 1 Ω
    B32-86 (E03) - Body ground
    Below 1 Ω
    B32-46 (E04) - Body ground
    Below 1 Ω
    B32-43 (ME01) - Body ground
    Below 1 Ω
    for Diesel Engine:
    Tester Connection
    Specified Condition
    B32-109 (E1) - Body ground
    Below 1 Ω
    B32-45 (E01) - Body ground
    Below 1 Ω
    B32-44 (E02) - Body ground
    Below 1 Ω
    B32-46 (E05) - Body ground
    Below 1 Ω

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    for Gasoline Engine:
    Tester Connection
    Condition
    Specified Condition
    A12-1 (+B2) - Body ground
    When battery's positive (+) voltage is applied to terminal MREL
    10 to 14 V
    A12-2 (+B) - Body ground
    When battery's positive (+) voltage is applied to terminal MREL
    10 to 14 V
    A12-3 (+BM) - Body ground
    Always
    10 to 14 V
    A12-20 (BATT) - Body ground
    Always
    10 to 14 V
    A12-28 (IGSW) - Body ground
    Ignition switch on (IG)
    10 to 14 V
    for Diesel Engine:
    Tester Connection
    Condition
    Specified Condition
    A12-2 (BATT) - Body ground
    Always
    10 to 14 V
    A12-1 (+B) - Body ground
    When battery's positive (+) voltage is applied to terminal MREL
    10 to 14 V
    A12-25 (IGSW) - Body ground
    Ignition switch on (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM


← Yaw Rate Sensor Communication Stop Mode (from Aug 2008)Main Body ECU Communication Stop Mode (from Nov 2005) →