2005-2008 RAV4 · Service Manual COMMUNICATION SYSTEM

Check CAN Bus Line (LHD Models)

Circuit diagnosis · Vehicles built from Aug 2008

Versions by build date: Nov 2005 – Jul 2008 from Aug 2008

DESCRIPTION

When any DTC for the CAN communication system is output, first measure the resistance between the terminals of the DLC3 to specify the trouble area, and check that there is not a short in the CAN main wire, between the main wire, to +B, or to GND.

WIRING DIAGRAM

C194056E01
C194057E01

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the main wire and the branch wire.
  2. For Auto:
    After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. For Reminder:
    After the ignition switch is turned off, check that the key reminder warning system and light reminder buzzer are not in operation.
  4. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.


NEXT


2. CHECK CAN BUS WIRE (MAIN WIRE FOR DISCONNECTION, CAN BUS LINES FOR SHORT CIRCUIT)

  1. H100769E34
    Measure the resistance of the DLC3.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Proceed to
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    54 to 69 Ω
    A
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    70 Ω or more
    B
    E16-6 (CANH) - E16-14 (CANL)
    Ignition switch off
    53 Ω or less
    C



B
CHECK CAN MAIN WIRE FOR OPEN (Click here)

C
CHECK CAN BUS LINES FOR SHORT CIRCUIT (Click here)
A


3. CHECK CAN BUS LINE FOR SHORT TO +B

  1. H100769E35
    Measure the resistance of the DLC3.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more
    E16-14 (CANL) - E16-16 (BAT)
    Ignition switch off
    1 MΩ or more



NG
CHECK CAN BUS LINE FOR SHORT TO +B (Click here)
OK


4. CHECK CAN BUS LINE FOR SHORT TO GND

  1. H100769E36
    Measure the resistance of the DLC3.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E16-6 (CANH) - E16-4 (CG)
    Ignition switch off
    200 Ω or more
    E16-14 (CANL) - E16-4 (CG)
    Ignition switch off
    200 Ω or more



NG
CHECK CAN BUS LINE FOR SHORT TO GND (Click here)
OK

HOW TO PROCEED WITH TROUBLESHOOTING (Click here)


← Check CAN Bus Line (LHD Models) (Nov 2005 – Jul 2008)Check CAN Bus Line (RHD Models) (Nov 2005 – Jul 2008) →