2005-2008 RAV4 · Service Manual COMMUNICATION SYSTEM

Air Conditioning Amplifier Communication Stop Mode

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

Detection Item
Symptom
Trouble Area
AIR CONDITIONING AMPLIFIER COMMUNICATION STOP MODE
  1. Air Conditioner is not displayed on "BUS CHECK" screen of intelligent tester
  2. Applies to "AIR CONDITIONING AMPLIFIER COMMUNICATION STOP MODE" in "DTC COMBINATION TABLE"
  1. Power source or inside air conditioning amplifier
  2. Air conditioning amplifier branch wire and connector
  3. Air conditioning amplifier

WIRING DIAGRAM

C129192E11
C129193E06

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the main wire and the branch wire.
  2. For Auto:
    After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. For Reminder:
    After the ignition switch is turned off, check that the key reminder warning system and light reminder buzzer are not in operation.
  4. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. CHECK CAN BUS LINE FOR DISCONNECTION (AIR CONDITIONING AMPLIFIER BRANCH WIRE)

  1. C128050E13
    Disconnect the E41*1 or E42*2 air conditioning amplifier connector.

    HINT:
    1. *1: for Automatic air conditioning system.
    2. *2: for Manual air conditioning system.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for Automatic Air Conditioning System:
    Tester Connection
    Condition
    Specified Condition
    E41-11 (CANH) - E41-12 (CANL)
    Ignition switch off
    54 to 69 Ω
    for Manual Air Conditioning System:
    Tester Connection
    Condition
    Specified Condition
    E42-8 (CANH) - E42-9 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CANH, CANL)
OK


2. CHECK WIRE HARNESS (AIR CONDITIONING AMPLIFIER - BATTERY AND BODY GROUND)

  1. C128050E14
    Disconnect the E41*1 or E42*2 air conditioning amplifier connectors.

    HINT:
    1. *1: for Automatic air conditioning system.
    2. *2: for Manual air conditioning system.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    for Automatic Air Conditioning System:
    Tester Connection
    Specified Condition
    E41-14 (GND) - Body ground
    Below 1 Ω
    for Manual Air Conditioning System:
    Tester Connection
    Specified Condition
    E42-24 (GND) - Body ground
    Below 1 Ω

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    for Automatic Air Conditioning System:
    Tester Connection
    Condition
    Specified Condition
    E41-21 (B) - Body ground
    Always
    10 to 14 V
    E41-1 (IG+) - Body ground
    Ignition switch on (IG)
    10 to 14 V
    for Manual Air Conditioning System:
    Tester Connection
    Condition
    Specified Condition
    E42-14 (IG+) - Body ground
    Ignition switch on (IG)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER


← ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode (from Aug 2008)Power Steering ECU Communication Stop Mode (from Nov 2005) →