2005-2008 RAV4 · Service Manual COMMUNICATION SYSTEM

ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode

Circuit diagnosis · Vehicles built from Aug 2008

Versions by build date: Nov 2005 – Jul 2008 from Aug 2008

DESCRIPTION

Detection Item
Symptom
Trouble Area
ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode
  1. ABS/VSC/TRC is not displayed on "Bus Check" screen of intelligent tester
  2. Applies to "ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode" in "DTC Combination Table"
  1. Power source or inside ABS and traction actuator (skid control ECU)
  2. ABS and traction actuator (skid control ECU) branch wire and connector
  3. ABS and traction actuator (skid control ECU)

HINT:
For vehicle with Vehicle Stability Control System only.


WIRING DIAGRAM

C132192E03

INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of the main wire and the branch wire.
  2. For Auto:
    After the ignition switch is turned off, check that the key reminder warning system is not in operation.
  3. For Reminder:
    After the ignition switch is turned off, check that the key reminder warning system and light reminder buzzer are not in operation.
  4. Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistance of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.


NEXT


2. CHECK FOR OPEN IN CAM BUS WIRE (ABS AND TRACTION ACTUATOR BRANCH WIRE)

  1. C154597E05
    Disconnect the A67 ABS and traction actuator (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    A67-25 (CANH) - A67-14 (CANL)
    Ignition switch off
    54 to 69 Ω



NG
REPAIR OR REPLACE ABS AND TRACTION ACTUATOR BRANCH WIRE OR CONNECTOR (CANH, CANL)
OK


3. CHECK HARNESS AND CONNECTOR (ABS AND TRACTION ACTUATOR - BATTERY AND BODY GROUND)
  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

  1. C154597E06
    Disconnect the A67 ABS and traction actuator (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A67-13 (GND2) - Body ground
    Always
    Below 1 Ω
    A67-1 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A67-34 (IG1) - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ABS AND TRACTION ACTUATOR ASSEMBLY


← ABS and Traction Actuator (Skid Control ECU) Communication Stop Mode (Nov 2005 – Jul 2008)Air Conditioning Amplifier Communication Stop Mode (from Nov 2005) →