2005-2008 RAV4 · Service Manual BODY ELECTRICAL

Front Fog Light Circuit

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

The main body ECU controls the front fog light relay (marking: FR FOG) when a signal is received from the headlight dimmer switch.

WIRING DIAGRAM

B118206E02

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (MAIN BODY ECU)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and press the intelligent tester main switch ON.

  1. Select the item below in the ACTIVE TEST and then check that the relay operates.

    Main body ECU 
    Item
    Test Details
    Diagnostic Note
    F Fog Light Rly
    Turn front fog light relay: ON / OFF
    -

    OK:
    Headlights (LOW) come on.



OK
Go to step 9
NG


2. CHECK TAILLIGHT
  1. Check that the taillights come on when the light control switch is turned on (TAIL).

    OK:
    Taillights come on.



NG
GO TO TAILLIGHT RELAY CIRCUIT
OK


3. INSPECT FUSE (FR FOG)
  1. Remove the FR FOG fuse from the instrument panel junction block.

  1. Measure the resistance of the fuse.

    Standard resistance:
    Below 1 Ω



NG
REPLACE FUSE
OK


4. INSPECT FOG LIGHT BULB
B128063E03
  1. Remove the fog light bulb.

  1. Connect the positive (+) lead from the battery to terminal 2 and the negative (-) lead to terminal 1, then check that the bulb illuminates.

    OK:
    Bulb illuminates.



NG
REPLACE FOG LIGHT BULB
OK


5. INSPECT FRONT FOG LIGHT RELAY (Marking: FR FOG)
B060778E79
  1. Remove the front fog light relay from the No. 6 relay block.

  1. Measure the resistance of the relay.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    (Battery voltage applied to terminals 1 and 2)



NG
REPLACE FRONT FOG LIGHT RELAY
OK


6. CHECK WIRE HARNESS (MAIN BODY ECU - BATTERY)
B129968E02
  1. Disconnect the E20 ECU connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E20-17 (FFGO) - Body ground
    Light control switch on (TAIL)
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


7. CHECK WIRE HARNESS (FRONT FOG LIGHT RELAY - BATTERY)
B128064E05
  1. Remove the front fog light relay from the No. 6 relay block.

  1. Measure the voltage of the relay block.

    Standard voltage:
    Tester Connection
    Specified Condition
    Relay block No. 6 front fog light relay terminal 5 - Body ground
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


8. CHECK WIRE HARNESS (FRONT FOG LIGHT RELAY - FRONT FOG LIGHT AND BODY GROUND)
B128065E06
  1. Remove the front fog light relay from the No. 6 relay block.

  1. Disconnect the A15 and A42 front fog light connectors.

  1. Measure the resistance of the wire harness side connectors and relay block.

    Standard resistance:
    Tester Connection
    Specified Condition
    Relay block front fog light relay terminal 3 - A15-2
    Below 1 Ω
    Relay block front fog light relay terminal 3 or A15-2 - Body ground
    10 kΩ or higher
    Relay block front fog light relay terminal 3 - A42-2
    Below 1 Ω
    Relay block front fog light relay terminal 3 or A42-2 - Body ground
    10 kΩ or higher
    A42-1 - Body ground
    Below 1 Ω
    A15-1 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK

9. CHECK WIRE HARNESS (DIMMER SWITCH - MAIN BODY ECU AND BODY GROUND)
B128010E03
  1. Disconnect the E15 headlight dimmer switch connector.

  1. Disconnect the E20 main body ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    for LH side 
    Tester Connection
    Specified Condition
    E20-13 (FFOG) - E15-4 (BFG)
    Below 1 Ω
    E20-13 (FFOG) or E15-4 (BFG) - Body ground
    10 kΩ or higher
    for RH side 
    Tester Connection
    Specified Condition
    E20-13 (FFOG) - E15-7 (BFG)
    Below 1 Ω
    E20-13 (FFOG) or E15-7 (BFG) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


10. INSPECT FOG LIGHT SWITCH
B128006E03
  1. Remove the headlight dimmer switch.

  1. Measure the resistance of the switch.

    Standard resistance:
    for LH side 
    Tester Connection
    Condition
    Specified Condition
    4 (BFG) - 3 (LFG)
    Fog light switch OFF
    10 kΩ or higher
    4 (BFG) - 3 (LFG)
    Fog light switch ON
    Below 1 Ω
    for RH side 
    Tester Connection
    Condition
    Specified Condition
    7 (BFG) - 8 (LFG)
    Fog light switch OFF
    10 kΩ or higher
    7 (BFG) - 8 (LFG)
    Fog light switch ON
    Below 1 Ω



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY
OK

REPAIR OR REPLACE HARNESS AND CONNECTOR (HEADLIGHT DIMMER SWITCH - BODY GROUND)


← Headlight (HI-BEAM) Circuit (from Nov 2005)Rear Fog Light Circuit (from Nov 2005) →