2005-2008 RAV4 · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007


1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

2. REMOVE FRONT WHEELS

3. DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. DISCHARGE FUEL SYSTEM PRESSURE procedures must be performed before disconnecting any part of the fuel system.
  2. After performing the DISCHARGE FUEL SYSTEM PRESSURE procedures, pressure will remain in the fuel line. When disconnecting the fuel line, place a cloth or equivalent over fittings to reduce the risk of fuel spray.

  1. Remove the console box (Click here).

  1. A128750E01
    Disconnect the connector.

  1. Start the engine. After the engine has stopped, turn the ignition switch off.

    HINT:
    DTC P0171 (system too lean) may be set.

  1. Check that the engine does not start.

  1. Remove the fuel tank cap, and let the air out of the fuel tank.

  1. A128750E01
    Connect the connector.

  1. Install the console box (Click here).


4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


5. DRAIN TRANSAXLE OIL
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


6. DRAIN TRANSFER OIL
  1. Remove the drain plug and gasket, and drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


7. REMOVE STARTER ASSEMBLY (for 1AZ-FE)
  1. Remove the starter (Click here).


8. REMOVE STARTER ASSEMBLY (for 2AZ-FE)
  1. for 1.6 kW Type:
    Remove the starter (Click here).

  1. for 1.7 kW Type:
    Remove the starter (Click here).


9. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

D026905E01
  1. Disconnect the back-up light switch connector.

  1. Remove the back up light switch and gasket from the manual transaxle case.


10. DISCONNECT CLUTCH RELEASE CYLINDER ASSEMBLY
  1. for 1AZ-FE:
    Disconnect the clutch release cylinder (Click here).

  1. for 2AZ-FE:
    Disconnect the clutch release cylinder (Click here).


11. DISCONNECT TRANSAXLE CONTROL CABLE ASSEMBLY

C127255
  1. Remove the 2 clips and 2 washers, and disconnect the 2 cables from the transaxle.

  1. Remove the 2 clips, and disconnect the 2 cables from the bracket.


12. REMOVE ENGINE ASSEMBLY WITH MANUAL TRANSAXLE
  1. for 1AZ-FE:
    Remove the engine with transaxle (Click here).

  1. for 2AZ-FE:
    Remove the engine with transaxle (Click here).


13. REMOVE TRANSFER ASSEMBLY

C126622
  1. Remove the 6 nuts, 2 bolts and transfer from the transaxle.


14. REMOVE FRONT ENGINE MOUNTING BRACKET

C129224
  1. Remove the 3 bolts and bracket.


15. REMOVE ENGINE MOUNTING BRACKET LH

C129226
  1. Remove the 3 bolts and bracket.


16. REMOVE REAR ENGINE MOUNTING BRACKET

C132314
  1. Remove the 3 bolts and mounting bracket.


17. REMOVE OIL PAN INSULATOR

C127239
  1. Remove the 2 bolts and insulator from the stiffener plate.


18. REMOVE STIFFENER PLATE LH

C127240
  1. Remove the 4 bolts and stiffener plate from the engine and transaxle assembly.


19. REMOVE STIFFENER PLATE RH

C127241
  1. Remove the 4 bolts and stiffener plate from the engine and transaxle assembly.


20. REMOVE MANUAL TRANSAXLE ASSEMBLY

D025747E01
  1. Remove the 10 bolts.

  1. Separate and remove the transaxle from the engine.


21. REMOVE MANUAL TRANSAXLE CASE PROTECTOR

D030076E01
  1. Remove the 2 bolts and case protector.

← REMOVAL (Nov 2005 – Dec 2006)REMOVAL (from Aug 2007) →