2005-2008 RAV4 · Service Manual BODY ELECTRICAL

Steering Pad Switch Circuit

Circuit diagnosis · Vehicles built from Nov 2005

DESCRIPTION

This circuit sends a signal from the steering pad switch to the radio receiver.

WIRING DIAGRAM

I102029E01

INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS such as the airbag. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the airbag system (Click here).


1. INSPECT STEERING PAD SWITCH ASSEMBLY
E126408E02
  1. Disconnect the switch connector.

  1. Measure the resistance of the switch.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    10 (AU1) - 8 (EAU)
    Not pushed
    100 kΩ or higher
    10 (AU1) - 8 (EAU)
    VOL+ switch pushed
    1 kΩ
    10 (AU1) - 8 (EAU)
    VOL- switch pushed
    3.11 kΩ
    10 (AU1) - 8 (EAU)
    SEEK+ switch pushed
    Below 1 Ω
    10 (AU1) - 8 (EAU)
    SEEK- switch pushed
    329 Ω
    9 (AU2) - 8 (EAU)
    Not pushed
    100 kΩ or higher
    9 (AU2) - 8 (EAU)
    MODE switch pushed
    Below 1 Ω
    9 (AU2) - 8 (EAU)
    ON HOOK switch pushed
    329 Ω
    9 (AU2) - 8 (EAU)
    OFF HOOK switch pushed
    1,000 Ω
    9 (AU2) - 8 (EAU)
    VOICE switch pushed
    3,110 Ω



NG
REPLACE STEERING PAD SWITCH ASSEMBLY
OK


2. CHECK WIRE HARNESS (SPIRAL CABLE - RADIO AND NAVIGATION ASSEMBLY)

  1. I043625E04
    Disconnect the E56 receiver connector.

  1. Disconnect the E10 cable connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E56-7 (SW1) - E10-6 (AU1)
    Below 1 Ω
    E56-8 (SW2) - E10-5 (AU2)
    Below 1 Ω
    E56-6 (SWG) - E10-4 (EAU)
    Below 1 Ω
    E56-7 (SW1) - Body ground
    10 kΩ or higher
    E56-8 (SW2) - Body ground
    10 kΩ or higher
    E56-6 (SWG) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3. INSPECT SPIRAL CABLE SUB-ASSEMBLY

  1. I102015E10
    Disconnect the cable connectors.

  1. Measure the resistance of the cable.

    Standard resistance:
    Tester Connection
    Specified Condition
    E10-4 (EAU) - 8 (EAU)
    Below 1 Ω
    E10-6 (AU1) - 10 (AU1)
    Below 1 Ω
    E10-5 (AU2) - 9 (AU2)
    Below 1 Ω



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY
OK

PROCEED TO NEXT INSPECTION PROCEDURE SHOWN IN PROBLEM SYMPTOMS TABLE


← The Other Caller cannot Hear Your Voice, or Your Voice is too Quiet or Distorted (from Nov 2005)Illumination Circuit (from Nov 2005) →