2005-2008 RAV4 · Service Manual TRANSMISSION

REPLACEMENT

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

HINT:
  1. Use the same procedure for the RH side (transaxle case oil seal) and LH side (transaxle case oil seal).
  2. The procedure listed below are for the LH side (transaxle case oil seal).


1. DRAIN TRANSAXLE OIL
  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and then drain the manual transaxle oil.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


2. DRAIN TRANSFER OIL
  1. Remove the drain plug and gasket, and then drain the manual transaxle oil.

  1. Install a new gasket and the drain plug.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


3. REMOVE FRONT WHEELS

4. REMOVE NO. 1 ENGINE UNDER COVER

5. REMOVE FRONT EXHAUST PIPE
  1. for 1AZ-FE:
    Remove front exhaust pipe (Click here).

  1. for 2AZ-FE:
    Remove front exhaust pipe (Click here).


6. REMOVE FRONT SPEED SENSOR LH

  1. C127964E01
    Disconnect the sensor connector.

  1. C127963E01
    Remove the sensor clip (labeled A), bolt (labeled B) and sensor clamp (labeled C).

  1. Remove the sensor clip (labeled D), bolt (labeled E) and sensor clamp (labeled F).

    C127962E01

  1. C127961E01
    Remove the bolt and sensor body from the knuckle.

    NOTICE:
    Keep the sensor tip and sensor installation hole free from foreign matter.


7. REMOVE FRONT SPEED SENSOR RH

HINT:
Use the same procedure for the RH side as for the LH side.


8. DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH

  1. C127528
    Remove the 2 nuts and stabilizer link.


9. DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.


10. DISCONNECT FRONT SUSPENSION NO. 1 LOWER ARM SUB-ASSEMBLY LH

C127531
  1. Remove the 2 nuts and bolt, and disconnect the lower arm from the ball joint.

  1. C127539
    Remove the bolt and nut from the suspension member (front side).

  1. C127540
    Remove the bolt and nut from the suspension member (rear side).


11. DISCONNECT FRONT SUSPENSION NO. 1 LOWER ARM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.


12. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

C127631E01
  1. Using SST, remove the front drive shaft.

    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    1. Be careful not to damage the transaxle case oil seal, inboard joint boot and drive shaft dust cover.
    2. Be careful not to drop the drive shaft assembly.


13. REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.


14. REMOVE TRANSFER ASSEMBLY

15. REMOVE TRANSAXLE CASE OIL SEAL LH

D025305E05
  1. Using SST, tap out the transaxle case oil seal.

    SST
    09308-00010  


16. REMOVE TRANSAXLE CASE OIL SEAL RH

C094266E04
SST
09308-00010  
  1. Using SST, tap out the transaxle case oil seal.


17. INSTALL TRANSAXLE CASE OIL SEAL LH
  1. Coat the lip of a new oil seal with MP grease.

  1. D026133E04
    Using SST and a hammer, tap in the oil seal.
    SST
    09608-10010  
    09950-70010   (09951-07200)

    Standard in depth:
    3.0 to 4.0 mm (0.118 to 0.158 in.)

    NOTICE:
    Be careful not to damage the lip of the oil seal.


18. INSTALL TRANSAXLE CASE OIL SEAL RH

D025722E02
  1. Coat the lip of a new transaxle case oil seal with MP grease.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09608-10010  
    09950-70010   (09951-07200)

    Standard depth:
    5.5 to 6.5 mm (0.217 to 0.256 in.)

    NOTICE:
    Be careful not to damage the lip of the oil seal.


19. INSTALL TRANSFER ASSEMBLY

C126622
  1. Install the transfer to the transaxle with the 6 nuts and 2 bolts.

    Torque:
    69 N*m{ 700 kgf*cm , 51 ft.*lbf }


20. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

C127700
  1. Coat the spline of the inboard joint shaft with gear oil.

  1. Using a brass bar and hammer, align the shaft splines in the drive shaft.

    NOTICE:
    1. Set the snap ring with the opening side facing downwards.
    2. Be careful not to damage the oil seal, boot and dust cover.


21. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.


22. CONNECT FRONT SUSPENSION NO. 1 LOWER ARM SUB-ASSEMBLY LH

  1. C127539
    Temporarily install the lower arm with the bolt and nut to the suspension member (front side).

  1. C127540
    Temporarily install the lower arm with the bolt and nut to the suspension member (rear side).


23. CONNECT FRONT SUSPENSION NO. 1 LOWER ARM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.


24. CONNECT FRONT STABILIZER LINK ASSEMBLY LH
  1. Install the link with the 2 nuts.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }


25. INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:
Use the same procedure for the RH side as for the LH side.


26. INSTALL FRONT SPEED SENSOR LH

NOTICE:
To prevent interference with other parts, do not twist the sensor wire's painted line areas when installing it.

  1. C127961E01
    Set the sensor body to the knuckle, and then install the sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Keep the sensor tip and sensor installation hole free from foreign matter.
    2. Firmly insert the sensor body into the knuckle before tightening the bolt.
    3. After installing the sensor to the knuckle, make sure that there is no clearance between the sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.
    4. To prevent interference between the sensor and magnetic rotor, do not rotate the sensor body during or after the insertion of the sensor body to the knuckle.

  1. Install the sensor clamp and sensor clip as follows.

    C127962E02

    1. Set the flexible hose clamp on the flexible hose bracket.

    2. Simultaneously perform the following: 1) hang the hook part of the sensor clamp (labeled A) on the part of the flexible hose bracket (labeled C); and 2) insert the hook part of the sensor clamp (labeled B) to the part of the flexible hose bracket (labeled D).

      NOTICE:
      Do not twist the sensor wire when installing the clamp.

    3. Tighten together the sensor clamp and the flexible hose clamp to the flexible hose bracket with the bolt (labeled E).

      Torque:
      18.5 N*m{ 189 kgf*cm , 14 ft.*lbf }

    4. Insert the sensor clip (labeled F) into the hole on the absorber lower bracket.

  1. C127963E02
    Install the sensor clamp, and sensor clip as follows.

    1. Set the sensor clamp (labeled G) on the side member, and then tighten it with the bolt (labeled H).

      Torque:
      8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

      NOTICE:
      Do not twist the sensor wire when installing the clamp.

    2. Insert the sensor clip (labeled I) into the hole on the apron.

  1. C127964E01
    Connect the sensor connector.


27. INSTALL FRONT SPEED SENSOR RH

HINT:
Use the same procedure for the RH side as for the LH side.


28. INSTALL FRONT EXHAUST PIPE
  1. for 1AZ-FE:
    Install front exhaust pipe (Click here).

  1. for 2AZ-FE:
    Install front exhaust pipe (Click here).


29. INSTALL NO. 1 ENGINE UNDER COVER

30. INSTALL FRONT WHEELS

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


31. ADD TRANSAXLE OIL

32. INSPECT MANUAL TRANSAXLE OIL
  1. Stop the vehicle in a level place.

  1. Remove the transaxle filler plug and gasket.

  1. D025304E21
    Check that the oil level is between 0 to 5 mm (0 to 0.20 in.) from the bottom lip of the filler plug opening. If the result is not as specified, add transaxle oil.

    Oil grade:
    GL-4

    Viscosity:
    SAE 75W

    Standard capacity:
    2.5 liters (2.6 US qts, 2.2 Imp. qts)

    NOTICE:
    1. Too much or too little oil will lead to transaxle problems.
    2. After adjusting the oil level, drive the vehicle and check the oil level again.

  1. Check for oil leakage if the oil level is low.

  1. Install the transaxle filler plug and a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


33. ADD TRANSFER OIL

34. INSPECT TRANSFER OIL

  1. C110905
    Remove the transfer case plug No. 2 (for filler) and gasket.

  1. Check that the oil level is between 0 to 5.0 mm (0 to 0.20 in.) from the bottom lip of the case plug (for filler) hole.
    If the result is not as specified, add transfer oil.

    Oil grade:
    GL-5

    Viscosity:
    SAE 80W-90

    Standard capacity:
    0.45 liter (0.48 US qts, 0.40 Imp. qts)

    NOTICE:
    1. When adding oil, pour it slowly.
    2. Too much or too little oil will lead to transfer problems.

  1. When the oil level is too low, check for oil leakage.

  1. Install a new gasket into the case plug (for filler) and then tighten the plug.

    Torque:
    39 N*m{ 398 kgf*cm , 28 ft.*lbf }


35. INSPECT FRONT WHEEL ALIGNMENT
  1. Inspect wheel alignment (Click here).

← REPLACEMENT (Nov 2005 – Dec 2006)REPLACEMENT (from Aug 2007) →