2005-2008 RAV4 · Service Manual DRIVE LINE

C1297/97 Steering Angle Sensor

Diagnostic trouble codes · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 Aug 2007 – Jul 2008 from Aug 2008

DESCRIPTION

  1. The 4WD control ECU determines that the vehicle is turning based on the signals sent from the steering angle sensor.
  1. The steering angle sensor signal is sent to the 4WD control ECU via the CAN communication system.
  1. The 4WD control ECU detects the amount of steering wheel movement and performs "slip control at vehicle start up", according to the amount of movement, and "slip control" to secure high turning performance.
DTC No.
DTC Detection Condition
Trouble Area
C1297/97
When voltage of 4WD control ECU IG1 terminal is 9.5 V or more, and steering angle sensor malfunction signal is received.
  1. Steering angle sensor
  1. CAN communication
  1. 4WD control ECU
  1. Wire harness

WIRING DIAGRAM

C163390E01

INSPECTION PROCEDURE

HINT:
Check the condition of each related circuit connector before troubleshooting (Click here).


1. CHECK FOR DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG) again and check that no CAN communication system DTC(s) is output.

  1. Start the engine.

  1. Drive the vehicle and turn the steering wheel to the right and left at a speed of 35 km/h (22 mph) and check that no brake control system (steering angle sensor) DTC (C1231/31) is output (Click here).


Result:
Result
Proceed to
Neither CAN communication system DTC nor brake control system DTC is output
A
CAN communication system DTC is output
B
Brake control system (steering angle sensor) DTC (C1231/31) is output
C

HINT:
When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.



B
REPAIR CIRCUIT INDICATOR OUTPUT CODE (CAN COMMUNICATION SYSTEM)

C
REPAIR OR REPLACE CIRCUIT INDICATOR OUTPUT CODE (STEERING ANGLE SENSOR CIRCUIT)
A


2. CHECK WIRE HARNESS (STEERING ANGLE SENSOR - BATTERY)
C135110E02
  1. Disconnect the E14 sensor connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E14-1 (IG) - Body ground
    Ignition switch on (IG)
    10 to 14 V
    E14-3 (BAT) - Body ground
    Always
    10 to 14 V



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


3. CHECK WIRE HARNESS (STEERING ANGLE SENSOR - BODY GROUND)
C107442E08
  1. Disconnect the E14 sensor connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E14-2 (ESS) - Body ground
    Below 1 Ω


    Result:
    Result
    Proceed to
    OK (When troubleshooting according to DTC chart)
    A
    OK (When troubleshooting according to PROBLEM SYMPTOMS TABLE)
    B
    NG
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C
REPAIR OR REPLACE HARNESS AND CONNECTOR
A

REPLACE STEERING ANGLE SENSOR


← C1297/97 Steering Angle Sensor (Nov 2005 – Dec 2006)C1297/97 Steering Angle Sensor (Aug 2007 – Jul 2008) →