2005-2008 RAV4 · Service Manual COMMUNICATION SYSTEM

B2326 CAN MS Bus Line Communication Malfunction

Diagnostic trouble codes · Vehicles built from Nov 2005

DESCRIPTION

DTC No.
Detection Item
Trouble Area
B2326
CAN No. 2 Bus Line Communication Malfunction
  1. CAN No. 2 bus circuit (No. 4 junction connector)
  2. Certification ECU branch wire and connector
  3. Main body ECU main wire and connector
  4. Combination meter ECU main wire and connector
  5. Main body ECU
  6. Combination meter ECU
  7. Certification ECU

HINT:
For vehicle with entry and start system only.


WIRING DIAGRAM

E116375E03

INSPECTION PROCEDURE


1. CHECK CAN BUS LINE (MAIN WIRE FOR DISCONNECTION, BUS LINES FOR SHORT CIRCUIT)
C129289E04
  1. Remove the instrument panel junction block with the connector connected.

  1. Disconnect the IB and IE junction block connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    Resistance of Malfunction
    E19-11 (CANP) - E19-12 (CANN)
    54 to 69 Ω
    Below 53 Ω: Short in line
    70 Ω or more: Open in CAN main bus line
    E19-11 (CANP) - IB-30 (BECU)
    1 MΩ or more
    Below 1 MΩ: +B short
    E19-12 (CANN) - IB-30 (BECU)
    1 MΩ or more
    Below 1 MΩ: +B short
    E19-11 (CANP) - IE-17 (GND1)
    200 Ω or more
    Below 200 Ω: Ground short
    E19-12 (CANN) - IE-17 (GND1)
    200 Ω or more
    Below 200 Ω: Ground short

    Result 
    Result
    Proceed to
    NG
    - Open in CAN main bus line
    A
    NG
    - Short in line
    - +B short
    - Ground short
    B
    OK
    C



B
Go to step 5

C
Go to step 10
A


2. CHECK CAN MAIN WIRE FOR DISCONNECTION (NO. 4 JUNCTION CONNECTOR)
F100894E42
  1. Disconnect the E76 junction connector (No. 4 junction connector).

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    Inspection Area
    E76-9 (MSCH) - E76-20 (MSCL)
    108 to 132 Ω
    Combination meter side CAN main wire
    E76-11 (CANP) - E76- 22 (CANN)
    108 to 132 Ω
    Main body ECU side CAN main wire

    Result 
    Result
    Proceed to
    NG (Combination meter side CAN main wire)
    A
    NG (Main body ECU side CAN main wire)
    B
    OK
    C



B
Go to step 4

C
REPAIR OR REPLACE NO. 4 JUNCTION CONNECTOR
A


3. CHECK CAN MAIN WIRE FOR DISCONNECTION (COMBINATION METER ECU)
C129295E02
  1. Disconnect the E76 junction connector (No. 4 junction connector).

  1. Remove the combination meter with the connector connected.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E22-9 (MSCH) - E22-10 (MSCL)
    108 to 132 Ω



NG
REPLACE COMBINATION METER ECU
OK

REPAIR OR REPLACE CAN MAIN WIRE AND CONNECTOR

4. CHECK CAN MAIN WIRE FOR DISCONNECTION (MAIN BODY ECU)
C129290E01
  1. Disconnect the E76 junction connector.

  1. Remove the instrument panel junction block with the connector connected.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E19-11 (CANP) - E19-12 (CANN)
    108 to 132 Ω



G
REPLACE INSTRUMENT PANEL JUNCTION BLOCK
OK

REPAIR OR REPLACE CAN MAIN WIRE AND CONNECTOR

5. CHECK CAN BUS LINE FOR SHORT
C129289E04
  1. Remove the instrument panel junction block with the connector connected.

  1. Disconnect the IB and IE junction block connectors.

  1. Disconnect the E22 meter connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E19-11 (CANP) - IB-30 (BECU)
    1 MΩ or more
    E19-12 (CANN) - IB-30 (BECU)
    1 MΩ or more
    E19-11 (CANP) - IE-17 (GND1)
    200 Ω or more
    E19-12 (CANN) - IE-17 (GND1)
    200 Ω or more
    E19-11 (CANP) - E19-12 (CANN)
    108 to 132 Ω

  1. Disconnect the E63 ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E19-11 (CANP) - IB-30 (BECU)
    1 MΩ or more
    E19-12 (CANN) - IB-30 (BECU)
    1 MΩ or more
    E19-11 (CANP) - IE-17 (GND1)
    200 Ω or more
    E19-12 (CANN) - IE-17 (GND1)
    200 Ω or more
    E19-11 (CANP) - E19-12 (CANN)
    108 to 132 Ω

    Result:
    Result
    Proceed to
    NG
    A
    OK (Combination meter)
    B
    OK (Certification ECU)
    C



B
REPLACE COMBINATION METER

C
REPLACE CERTIFICATION ECU
A


6. CHECK CAN BUS LINE FOR SHORT
C129289E04
  1. Remove the instrument panel junction block with the connector connected.

  1. Disconnect the IE and IB junction block connectors.

  1. Disconnect the E76 junction connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E19-11 (CANP) - IB-30 (BECU)
    1 MΩ or more
    E19-12 (CANN) - IB-30 (BECU)
    1 MΩ or more
    E19-11 (CANP) - IE-17 (GND1)
    200 Ω or more
    E19-12 (CANN) - IE-17 (GND1)
    200 Ω or more
    E19-11 (CANP) - E19-12 (CANN)
    108 to 132 Ω



OK
Go to step 8
NG


7. CHECK CAN BUS LINE FOR SHORT
C129296E03
  1. Disconnect the E19 ECU connector.

  1. Disconnect the IB and IE junction block connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E19-11 (CANP) - IB-30 (BECU)
    1 MΩ or more
    E19-12 (CANN) - IB-30 (BECU)
    1 MΩ or more
    E19-11 (CANP) - IE-17 (GND1)
    200 Ω or more
    E19-12 (CANN) - IE-17 (GND1)
    200 Ω or more
    E19-11 (CANP) - E19-12 (CANN)
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE AND CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK

8. CHECK CAN BUS LINE FOR SHORT
C129294E02
  1. Disconnect the E76 junction connector.

  1. Disconnect the E22 meter connector.

  1. Measure the resistance of the wire harness side connector.

    Standard resistance:
    Tester Connection
    Specified Condition
    E22-9 (CANP) - E22-10 (CANN)
    108 to 132 Ω
    E22-9 (CANP) - E22-22 (B)
    1 MΩ or more
    E22-10 (CANN) - E22-22 (B)
    1 MΩ or more
    E22-9 (CANP) - E22-33 (ET)
    200 Ω or more
    E22-10 (CANN) - E22-33 (ET)
    200 Ω or more

    Result 
    Result
    Proceed to
    OK
    w/ Entry and start system
    A
    OK
    w/o Entry and start system
    B
    NG
    C



B
REPLACE COMBINATION METER ECU

C
REPAIR OR REPLACE CAN MAIN WIRE AND CONNECTOR
A


9. CHECK CAN BUS LINE FOR SHORT
C129293E01
  1. Disconnect the E76 junction connector.

  1. Disconnect the E63 ECU connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance:
    Tester Connection
    Specified Condition
    E63-27 (CANH) - E63-28 (CANL)
    54 to 69 Ω
    E63-27 (CANH) - E63-1 (+B1)
    1 MΩ or more
    E63-28 (CANL) - E63-1 (+B1)
    1 MΩ or more
    E63-27 (CANH) - E63-17 (E)
    200 Ω or more
    E63-28 (CANL) - E63-17 (E)
    200 Ω or more



NG
REPLACE CERTIFICATION ECU OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE CERTIFICATION ECU

10. CHECK CAN BUS LINE FOR DISCONNECTION
  1. Recheck for DTC.


NEXT

GO TO DTC CHART


← B1207 Certification ECU Communication Malfunction (from Nov 2005)Brake Actuator (Skid Control ECU) Communication Stop Mode (from Nov 2005) →