2005-2008 RAV4 · Service Manual SUSPENSION & AXLE

REMOVAL

Removal / installation · Vehicles built Jan 2007 – Jul 2007

Versions by build date: Nov 2005 – Dec 2006 Jan 2007 – Jul 2007 from Aug 2007

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are the LH side.


1. REMOVE FRONT WHEEL

2. DRAIN AUTOMATIC TRANSAXLE FLUID
  1. Drain the automatic transaxle fluid for U140F (Click here).

  1. Drain the automatic transaxle fluid for U241E (Click here).


3. DRAIN TRANSAXLE OIL
  1. Drain the transaxle oil for E352F/E359 (Click here).

  1. Drain the transaxle oil for E352 (Click here).

  1. Drain the transaxle oil for EA64F (Click here).


4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


5. REMOVE FRONT AXLE SHAFT LH NUT

C129483E01
  1. Using SST and a hammer, unstake the staked part of the nut.

    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the screw of the drive shaft may be damaged.

  1. While applying the brakes, remove the lock axle hub nut.


6. REMOVE FRONT SPEED SENSOR LH

  1. C127964E01
    Disconnect the sensor connector.

  1. C127963E01
    Remove the sensor clip (labeled A), bolt (labeled B) and sensor clamp (labeled C).

  1. Remove the sensor clip (labeled D), bolt (labeled E) and sensor clamp (labeled F).

    C127962E01

  1. C127961E01
    Remove the bolt and sensor body from the knuckle.

    NOTICE:
    Keep the sensor tip and sensor installation hole free from foreign matter.


7. REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY LH

C127058
  1. Remove the 2 bolts and cylinder.


8. REMOVE FRONT DISC

  1. C127063E01
    Put matchmarks on the disc and axle hub.

  1. Remove the disc.


9. DISCONNECT TIE ROD END SUB-ASSEMBLY LH
  1. Remove the cotter pin and castle nut.

  1. C132680E01
    Using SST, disconnect the tie rod end from the steering knuckle.

    NOTICE:
    Do not damage the tie rod end dust cover.

    SST
    09628-62011  


10. DISCONNECT FRONT SUSPENSION NO. 1 LOWER ARM SUB-ASSEMBLY LH

C127531
  1. Remove the bolt and 2 nuts.

  1. Disconnect the lower arm from the ball joint.


11. REMOVE STEERING KNUCKLE WITH AXLE HUB

C127533
  1. Remove the 2 bolts and 2 nuts, and disconnect the shock absorber from the steering knuckle.

    HINT:
    While fixing the nuts in place, loosen and remove the bolts.

  1. C129488E01
    Put matchmarks on the drive shaft and the axle hub.

  1. Using a plastic-faced hammer, remove the steering knuckle with axle hub.

    NOTICE:
    Be careful not to damage the boot and speed sensor rotor. Do not excessively push out the drive shaft from the axle assembly.


12. REMOVE FRONT LOWER BALL JOINT ASSEMBLY LH

C127535E01
  1. Remove the clip and nut.

  1. Using SST, remove the front lower ball joint assembly.

    SST
    09628-62011  


13. REMOVE FRONT AXLE HUB SUB-ASSEMBLY LH

C127536
  1. Remove the 4 bolts and axle hub from the steering knuckle.

    NOTICE:
    Do not place the hub and bearing's magnet rotor side so that it is facing downward, and do not allow the magnet rotor side to become damaged or contact foreign matter.

  1. Remove the dust cover from the steering knuckle.

← REMOVAL (Nov 2005 – Dec 2006)REMOVAL (from Aug 2007) →