VEHICLE STABILITY CONTROL SYSTEM > DTC CHECK / CLEAR |
| CHECK DTC (When Using Intelligent Tester) |
Turn the ignition switch off and connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Read the DTCs by following the prompts on the intelligent tester screen.
| CLEAR DTC (When Using Intelligent Tester) |
Turn the ignition switch off and connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Operate the intelligent tester to clear the DTCs.
| CHECK DTC (When not Using Intelligent Tester) |
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the ignition switch to ON.
w/ Multi Information Display:
Read DTCs from the multi information display on the combination meter.
w/o Multi Information Display:
Read DTCs from the ABS warning light and slip indicator light on the combination meter.
| Trouble Area | See Procedure |
| ABS warning light circuit |
Click here or Click here
|
| Slip indicator light circuit |
Click here or Click here
|
| TC and CG terminal circuit |
Click here
|

Check the details of the DTCs.
| Multi Information Display ABS Warning Light Display | Intelligent Tester Display |
| 11 | C0278 |
| 12 | C0279 |
| 13 | C0273 |
| 14 | C0274 |
| 21 | C0226 |
| 22 | C0236 |
| 23 | C0246 |
| 24 | C0256 |
| 25 | C1225 |
| 31 | C1401 |
| C1405 | |
| 32 | C1402 |
| C1406 | |
| 33 | C1403 |
| C1407 | |
| 34 | C1404 |
| C1408 | |
| 35 | C1413 |
| 36 | C1414 |
| 37 | C1337 |
| 38 | C1415 |
| 39 | C1416 |
| 41 | C1241 |
| C1417 | |
| 43 | C1243 |
| 44 | C1419 |
| C1420 | |
| C1442 | |
| 45 | C1245 |
| 46 | C1421 |
| C1422 | |
| C1423 | |
| C1424 | |
| 49 | C1425 |
| C1426 | |
| 51 | C1427 |
| C1428 | |
| 67 | C1429 |
| C1430 | |
| C1431 | |
| 91 | C1361 |
| 94 | U0073 |
| 95 | U0124 |
| 97 | C1381 |
| Multi Information Display Slip Indicator Light Display | Intelligent Tester Display |
| 31 | C1432 |
| C1433 | |
| C1434 | |
| 32 | C1232 |
| 34 | C1435 |
| C1436 | |
| C1443 | |
| 36 | C1210 |
| 39 | C1336 |
| 43 (*1) | - |
| 51 | C1201 |
| 53 | C1203 |
| 62 | U0123 |
| 63 | U0126 |
| 64 | C1380 |
| 65 | C1437 |
| U0100 | |
| 66 | C1290 |
| C1439 | |
| C1445 | |
| 98 | C1440 |
| C1441 |
After completing the check, disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3, and turn the ignition switch off.
| CLEAR DTC (When not Using Intelligent Tester) |
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Turn the ignition switch to ON.
![]() |
Clear the DTCs stored in the skid control ECU by depressing the brake pedal 8 times or more within 5 seconds.
Check that the ABS warning light and slip indicator light come on.
Remove SST from the terminals of the DLC3.
Turn the ignition switch off.
| END OF DTC CHECK/CLEAR |
Turn the ignition switch to ON.
Check that the ABS warning light and slip indicator light go off within approximately 3 seconds.
Turn the ignition switch off.