Home › TRANSMISSION · U660F AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM

DTC    P0712    Transmission Fluid Temperature Sensor "A" Circuit Low Input

DTC    P0713    Transmission Fluid Temperature Sensor "A" Circuit High Input

for Preparation Click here


DESCRIPTION

Refer to DTC P0711 .

DTC Code
DTC Detection Condition
Trouble Area
P0712
ATF temperature sensor resistance is less than 79 Ω for 0.5 sec. or more (1-trip detection logic).
  1. Short in ATF temperature sensor circuit
  2. Transmission wire
  3. ATF temperature sensor (ATF temperature sensor assembly)
  4. TCM
P0713
ATF temperature sensor resistance is more than 156 kΩ for 0.5 sec. or more when 15 minutes or more have elapsed after the engine starts (1-trip detection logic).
  1. Open in ATF temperature sensor circuit
  2. Transmission wire
  3. ATF temperature sensor (ATF temperature sensor assembly)
  4. TCM

MONITOR DESCRIPTION

These DTCs indicate an open or short in the ATF temperature sensor circuit. The ATF temperature sensor converts ATF temperature into an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature, and the TCM detects an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature is less than 79 Ω*1 or more than 156 kΩ*2, the TCM interprets this as a fault in the ATF sensor or wiring. The TCM will turn on the MIL and store the DTC.

HINT:
  1. The ATF temperature can be checked on the intelligent tester display.
  2. *1: 150°C (302°F) or more is indicated regardless of the actual ATF temperature.
  3. *2: -40°C (-40°F) is indicated regardless of the actual ATF temperature.


WIRING DIAGRAM


C206309E01


INSPECTION PROCEDURE

Refer to DTC P0711 .
1.INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)


    C207057E01
  1. Remove the TCM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    18 (THO1) - 17 (E2)
    Always
    79 Ω to 156 kΩ
    18 (THO1) - Body ground
    Always
    10 kΩ or higher
    17 (E2) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

    Resistance (Reference):
    ATF Temperature
    Specified Condition
    10°C (50°F)
    5 to 8 kΩ
    25°C (77°F)
    2.5 to 4.5 kΩ
    110°C (230°F)
    0.22 to 0.28 kΩ

Text in Illustration 
*1
Component without TCM connected
(Transmission Wire)


NG
Go to step 2
OK

REPLACE TCM (Click here)  

2.INSPECT ATF TEMPERATURE SENSOR


    C206308E01
  1. Disconnect the ATF temperature sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    THO1 - E2
    Always
    79 Ω to 156 kΩ
    THO1 - Body ground
    Always
    10 kΩ or higher
    E2 - Body ground
    Always
    10 kΩ or higher

    HINT:
    If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

    Resistance (Reference):
    ATF Temperature
    Specified Condition
    10°C (50°F)
    5 to 8 kΩ
    25°C (77°F)
    2.5 to 4.5 kΩ
    110°C (230°F)
    0.22 to 0.28 kΩ

Text in Illustration 
*1
Component without harness connected
(ATF Temperature Sensor Assembly)


NG
REPLACE ATF TEMPERATURE SENSOR (ATF TEMPERATURE SENSOR ASSEMBLY) (Click here)
OK

REPLACE TRANSMISSION WIRE (Click here)