Home › ENGINE · 2AD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for CCo)

DTC    P0724    Brake Switch "B" Circuit High

for Preparation Click here


DESCRIPTION

This DTC indicates that the stop light switch remains ON. When the stop light switch remains ON during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC.

P0724 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times.
Stop light switch remains on even when vehicle is driven in GO (30 km/h (19 mph) or more) and STOP (less than 3 km/h (1.8 mph)) pattern 5 times.
(2 trip detection logic)
  1. Short in stop light switch signal circuit
  2. Stop light switch assembly
  3. ECM

Related Data List 
DTC No.
Data List
P0724
Stop Light Switch

WIRING DIAGRAM


A160611E05


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

  1. Read the value displayed on the tester when the brake pedal is depressed and released.

    OK:
    Brake Pedal
    Display
    Released
    OFF
    Depressed
    ON



OK
Go to step 7

NG
Go to step 2

2.INSPECT STOP LIGHT SWITCH ASSEMBLY
C171632E05
  1. Remove the stop light switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin not pushed
    Below 1 Ω
    Switch pin pushed
    10 kΩ or higher
    3 - 4
    Switch pin not pushed
    10 kΩ or higher
    Switch pin pushed
    Below 1 Ω

  1. Reinstall the stop light switch.



NG
Go to step 5
OK


3.CHECK ECM (STP VOLTAGE)
A112585E60
  1. Disconnect the ECM connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Brake Pedal Condition
    Specified Condition
    A12-35 (STP) - Body ground
    Released
    0 to 3 V
    Depressed
    11 to 14 V

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


4.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7

5.REPLACE STOP LIGHT SWITCH ASSEMBLY
  1. Replace the stop light switch assembly (Click here).



NEXT
Go to step 7

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine.

  1. Accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less 5 times or more.

  1. Confirm that the DTC is not output again.

    HINT:
    Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.

    1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

    2. Input DTC P0724.

    3. Check that STATUS is NORMAL.

      HINT:
      1. If STATUS is NORMAL, DTC judgment is complete and the system is determined to be normal.
      2. If STATUS is INCOMPLETE or UNKNOWN, DTC judgment is incomplete. Perform the following procedure again 5 times: accelerate the vehicle to 30 km/h (19 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.8 mph) or less.


NEXT

END